CONFIG_FLASH_BASE_ADDRESS¶

Flash Base Address

Type: hex

Help¶

This option specifies the base address of the flash on the board. It is normally set by the board’s defconfig file and the user should generally avoid modifying it via the menu configuration.

Direct dependencies¶

(!XIP && BOARD_96B_MEERKAT96) || (!XIP && BOARD_COLIBRI_IMX7D_M4) || (!XIP && BOARD_PICO_PI_M4) || (!XIP && BOARD_WARP7_M4) || BOARD_HIFIVE1_REVB || (CODE_ITCM && SOC_SERIES_IMX_RT) || (CODE_FLEXSPI && SOC_SERIES_IMX_RT) || (CODE_FLEXSPI2 && SOC_SERIES_IMX_RT) || (!XIP && SOC_CC3220SF && SOC_SERIES_CC32XX) || (!XIP && SOC_CC3235SF && SOC_SERIES_CC32XX) || SOC_XILINX_ZYNQMP || (FLASH && SOC_OPENISA_RV32M1_RISCV32) || ARC || ARM || NIOS2 || X86

(Includes any dependencies from ifs and menus.)

Defaults¶

0
0
0
0
0x0
0x0
0x0
0x0
0
0
0x0
0x0
0x0 if (XIP && ARM) || !ARM

Kconfig definitions¶

At boards/arm/96b_meerkat96/Kconfig.defconfig:28

Included via Kconfig:8 → Kconfig.zephyr:26

Menu path: (Top)

config FLASH_BASE_ADDRESS
    hex
    default 0
    depends on !XIP && BOARD_96B_MEERKAT96

At boards/arm/colibri_imx7d_m4/Kconfig.defconfig:69

Included via Kconfig:8 → Kconfig.zephyr:26

Menu path: (Top)

config FLASH_BASE_ADDRESS
    hex
    default 0
    depends on !XIP && BOARD_COLIBRI_IMX7D_M4

At boards/arm/pico_pi_m4/Kconfig.defconfig:22

Included via Kconfig:8 → Kconfig.zephyr:26

Menu path: (Top)

config FLASH_BASE_ADDRESS
    hex
    default 0
    depends on !XIP && BOARD_PICO_PI_M4

At boards/arm/warp7_m4/Kconfig.defconfig:52

Included via Kconfig:8 → Kconfig.zephyr:26

Menu path: (Top)

config FLASH_BASE_ADDRESS
    hex
    default 0
    depends on !XIP && BOARD_WARP7_M4

At boards/riscv/hifive1_revb/Kconfig.defconfig:12

Included via Kconfig:8 → Kconfig.zephyr:26

Menu path: (Top)

config FLASH_BASE_ADDRESS
    hex
    default 0x0
    depends on BOARD_HIFIVE1_REVB

At soc/arm/nxp_imx/rt/Kconfig.defconfig.series:102

Included via Kconfig:8 → Kconfig.zephyr:28 → soc/arm/nxp_imx/Kconfig.defconfig:4

Menu path: (Top)

config FLASH_BASE_ADDRESS
    hex
    default 0x0
    depends on CODE_ITCM && SOC_SERIES_IMX_RT

At soc/arm/nxp_imx/rt/Kconfig.defconfig.series:112

Included via Kconfig:8 → Kconfig.zephyr:28 → soc/arm/nxp_imx/Kconfig.defconfig:4

Menu path: (Top)

config FLASH_BASE_ADDRESS
    hex
    default 0x0
    depends on CODE_FLEXSPI && SOC_SERIES_IMX_RT

At soc/arm/nxp_imx/rt/Kconfig.defconfig.series:122

Included via Kconfig:8 → Kconfig.zephyr:28 → soc/arm/nxp_imx/Kconfig.defconfig:4

Menu path: (Top)

config FLASH_BASE_ADDRESS
    hex
    default 0x0
    depends on CODE_FLEXSPI2 && SOC_SERIES_IMX_RT

At soc/arm/ti_simplelink/cc32xx/Kconfig.defconfig.cc3220sf:48

Included via Kconfig:8 → Kconfig.zephyr:28 → soc/arm/ti_simplelink/Kconfig.defconfig:3 → soc/arm/ti_simplelink/cc32xx/Kconfig.defconfig.series:7

Menu path: (Top)

config FLASH_BASE_ADDRESS
    hex
    default 0
    depends on !XIP && SOC_CC3220SF && SOC_SERIES_CC32XX

At soc/arm/ti_simplelink/cc32xx/Kconfig.defconfig.cc3235sf:49

Included via Kconfig:8 → Kconfig.zephyr:28 → soc/arm/ti_simplelink/Kconfig.defconfig:3 → soc/arm/ti_simplelink/cc32xx/Kconfig.defconfig.series:7

Menu path: (Top)

config FLASH_BASE_ADDRESS
    hex
    default 0
    depends on !XIP && SOC_CC3235SF && SOC_SERIES_CC32XX

At soc/arm/xilinx_zynqmp/Kconfig.defconfig:37

Included via Kconfig:8 → Kconfig.zephyr:28

Menu path: (Top)

config FLASH_BASE_ADDRESS
    hex
    default 0x0
    depends on SOC_XILINX_ZYNQMP

At soc/riscv/openisa_rv32m1/Kconfig.defconfig:174

Included via Kconfig:8 → Kconfig.zephyr:28

Menu path: (Top)

config FLASH_BASE_ADDRESS
    hex
    default 0x0
    depends on FLASH && SOC_OPENISA_RV32M1_RISCV32

At arch/Kconfig:120

Included via Kconfig:8 → Kconfig.zephyr:34

Menu path: (Top) → General Architecture Options

config FLASH_BASE_ADDRESS
    hex "Flash Base Address"
    default 0x0 if (XIP && ARM) || !ARM
    depends on ARC || ARM || NIOS2 || X86
    help
      This option specifies the base address of the flash on the board. It is
      normally set by the board's defconfig file and the user should generally
      avoid modifying it via the menu configuration.

(The ‘depends on’ condition includes propagated dependencies from ifs and menus.)

Zephyr

nRF Connect SDK

nrfxlib

MCUboot