SPI Interface

SPI Interface . More...

Data Structures
struct	spi_cs_control
	SPI Chip Select control structure. More...
struct	spi_config
	SPI controller configuration structure. More...
struct	spi_dt_spec
	Complete SPI DT information. More...
struct	spi_buf
	SPI buffer structure. More...
struct	spi_buf_set
	SPI buffer array structure. More...
struct	spi_driver_api
	SPI driver API This is the mandatory API any SPI driver needs to expose. More...

Macros
#define	SPI_CS_GPIOS_DT_SPEC_GET(spi_dev)
	Get a struct gpio_dt_spec for a SPI device's chip select pin.
#define	SPI_CS_GPIOS_DT_SPEC_INST_GET(inst)
	Get a struct gpio_dt_spec for a SPI device's chip select pin.
#define	SPI_CS_CONTROL_INIT(node_id, delay_)
	Initialize and get a pointer to a spi_cs_control from a devicetree node identifier.
#define	SPI_CS_CONTROL_INIT_INST(inst, delay_)
	Get a pointer to a spi_cs_control from a devicetree node.
#define	SPI_CONFIG_DT(node_id, operation_, delay_)
	Structure initializer for spi_config from devicetree.
#define	SPI_CONFIG_DT_INST(inst, operation_, delay_)
	Structure initializer for spi_config from devicetree instance.
#define	SPI_DT_SPEC_GET(node_id, operation_, delay_)
	Structure initializer for spi_dt_spec from devicetree.
#define	SPI_DT_SPEC_INST_GET(inst, operation_, delay_)
	Structure initializer for spi_dt_spec from devicetree instance.
#define	SPI_MOSI_OVERRUN_UNKNOWN   0x100
	Value that will never compare true with any valid overrun character.
#define	SPI_MOSI_OVERRUN_DT(node_id)
	The value sent on MOSI when all TX bytes are sent, but RX continues.
#define	SPI_MOSI_OVERRUN_DT_INST(inst)
	The value sent on MOSI when all TX bytes are sent, but RX continues.
#define	SPI_DEVICE_DT_DEFINE(node_id, init_fn, pm, data, config, level, prio, api, ...)
#define	SPI_STATS_RX_BYTES_INC(dev_)
#define	SPI_STATS_TX_BYTES_INC(dev_)
#define	SPI_STATS_TRANSFER_ERROR_INC(dev_)
#define	spi_transceive_stats(dev, error, tx_bufs, rx_bufs)
#define	SPI_DT_IODEV_DEFINE(name, node_id, operation_, delay_)
	Define an iodev for a given dt node on the bus.

Typedefs
typedef uint16_t	spi_operation_t
	Opaque type to hold the SPI operation flags.
typedef int(*	spi_api_io) (const struct device *dev, const struct spi_config *config, const struct spi_buf_set *tx_bufs, const struct spi_buf_set *rx_bufs)
	Callback API for I/O See spi_transceive() for argument descriptions.
typedef void(*	spi_callback_t) (const struct device *dev, int result, void *data)
	SPI callback for asynchronous transfer requests.
typedef int(*	spi_api_io_async) (const struct device *dev, const struct spi_config *config, const struct spi_buf_set *tx_bufs, const struct spi_buf_set *rx_bufs, spi_callback_t cb, void *userdata)
typedef int(*	spi_api_release) (const struct device *dev, const struct spi_config *config)
	Callback API for unlocking SPI device.

Functions
static bool	spi_cs_is_gpio (const struct spi_config *config)
	Check if SPI CS is controlled using a GPIO.
static bool	spi_cs_is_gpio_dt (const struct spi_dt_spec *spec)
	Check if SPI CS in spi_dt_spec is controlled using a GPIO.
static bool	spi_is_ready_dt (const struct spi_dt_spec *spec)
	Validate that SPI bus (and CS gpio if defined) is ready.
int	spi_transceive (const struct device *dev, const struct spi_config *config, const struct spi_buf_set *tx_bufs, const struct spi_buf_set *rx_bufs)
	Read/write the specified amount of data from the SPI driver.
static int	spi_transceive_dt (const struct spi_dt_spec *spec, const struct spi_buf_set *tx_bufs, const struct spi_buf_set *rx_bufs)
	Read/write data from an SPI bus specified in spi_dt_spec.
static int	spi_read (const struct device *dev, const struct spi_config *config, const struct spi_buf_set *rx_bufs)
	Read the specified amount of data from the SPI driver.
static int	spi_read_dt (const struct spi_dt_spec *spec, const struct spi_buf_set *rx_bufs)
	Read data from a SPI bus specified in spi_dt_spec.
static int	spi_write (const struct device *dev, const struct spi_config *config, const struct spi_buf_set *tx_bufs)
	Write the specified amount of data from the SPI driver.
static int	spi_write_dt (const struct spi_dt_spec *spec, const struct spi_buf_set *tx_bufs)
	Write data to a SPI bus specified in spi_dt_spec.
static int	spi_transceive_cb (const struct device *dev, const struct spi_config *config, const struct spi_buf_set *tx_bufs, const struct spi_buf_set *rx_bufs, spi_callback_t callback, void *userdata)
	Read/write the specified amount of data from the SPI driver.
static int	spi_transceive_signal (const struct device *dev, const struct spi_config *config, const struct spi_buf_set *tx_bufs, const struct spi_buf_set *rx_bufs, struct k_poll_signal *sig)
	Read/write the specified amount of data from the SPI driver.
static int	spi_read_signal (const struct device *dev, const struct spi_config *config, const struct spi_buf_set *rx_bufs, struct k_poll_signal *sig)
	Read the specified amount of data from the SPI driver.
static int	spi_write_signal (const struct device *dev, const struct spi_config *config, const struct spi_buf_set *tx_bufs, struct k_poll_signal *sig)
	Write the specified amount of data from the SPI driver.
static void	spi_iodev_submit (struct rtio_iodev_sqe *iodev_sqe)
	Submit a SPI device with a request.
static bool	spi_is_ready_iodev (const struct rtio_iodev *spi_iodev)
	Validate that SPI bus (and CS gpio if defined) is ready.
int	spi_release (const struct device *dev, const struct spi_config *config)
	Release the SPI device locked on and/or the CS by the current config.
static int	spi_release_dt (const struct spi_dt_spec *spec)
	Release the SPI device specified in spi_dt_spec.

Variables
const struct rtio_iodev_api	spi_iodev_api

SPI operational mode
#define	SPI_OP_MODE_MASTER   0U
	Master mode.
#define	SPI_OP_MODE_SLAVE   BIT(0)
	Slave mode.
#define	SPI_OP_MODE_GET(_operation_)
	Get SPI operational mode.

SPI Polarity & Phase Modes
#define	SPI_MODE_CPOL   BIT(1)
	Clock Polarity: if set, clock idle state will be 1 and active state will be 0.
#define	SPI_MODE_CPHA   BIT(2)
	Clock Phase: this dictates when is the data captured, and depends clock's polarity.
#define	SPI_MODE_LOOP   BIT(3)
	Whatever data is transmitted is looped-back to the receiving buffer of the controller.
#define	SPI_MODE_GET(_mode_)
	Get SPI polarity and phase mode bits.

SPI Transfer modes (host controller dependent)
#define	SPI_TRANSFER_MSB   (0U)
	Most significant bit first.
#define	SPI_TRANSFER_LSB   BIT(4)
	Least significant bit first.

SPI word size
#define	SPI_WORD_SIZE_GET(_operation_)
	Get SPI word size.
#define	SPI_WORD_SET(_word_size_)
	Set SPI word size.

Specific SPI devices control bits
#define	SPI_HOLD_ON_CS   BIT(12)
	Requests - if possible - to keep CS asserted after the transaction.
#define	SPI_LOCK_ON   BIT(13)
	Keep the device locked after the transaction for the current config.
#define	SPI_CS_ACTIVE_HIGH   BIT(14)
	Active high logic on CS.

SPI MISO lines
Some controllers support dual, quad or octal MISO lines connected to slaves. Default is single, which is the case most of the time. Without CONFIG_SPI_EXTENDED_MODES being enabled, single is the only supported one.
#define	SPI_LINES_SINGLE   (0U << 16)
	Single line.
#define	SPI_LINES_DUAL   (1U << 16)
	Dual lines.
#define	SPI_LINES_QUAD   (2U << 16)
	Quad lines.
#define	SPI_LINES_OCTAL   (3U << 16)
	Octal lines.
#define	SPI_LINES_MASK   (0x3U << 16)
	Mask for MISO lines in spi_operation_t.

SPI duplex mode
Some controllers support half duplex transfer, which results in 3-wire usage. By default, full duplex will prevail.
#define	SPI_FULL_DUPLEX   (0U << 11)
#define	SPI_HALF_DUPLEX   (1U << 11)

SPI Frame Format
2 frame formats are exposed: Motorola and TI. The main difference is the behavior of the CS line. In Motorola it stays active the whole transfer. In TI, it's active only one serial clock period prior to actually make the transfer, it is thus inactive during the transfer, which ends when the clocks ends as well. By default, as it is the most commonly used, the Motorola frame format will prevail.
#define	SPI_FRAME_FORMAT_MOTOROLA   (0U << 15)
#define	SPI_FRAME_FORMAT_TI   (1U << 15)

Detailed Description

SPI Interface .

SPI Interface .

Since

1.0

Version

1.0.0

Macro Definition Documentation

SPI_CONFIG_DT

#define SPI_CONFIG_DT	(		node_id,
			operation_,
			delay_ )

#include <zephyr/drivers/spi.h>

Value:

        {                                                               \
                .frequency = DT_PROP(node_id, spi_max_frequency),       \
                .operation = (operation_) |                             \
                        DT_PROP(node_id, duplex) |                      \
                        DT_PROP(node_id, frame_format) |                        \
                        COND_CODE_1(DT_PROP(node_id, spi_cpol), SPI_MODE_CPOL, (0)) |   \
                        COND_CODE_1(DT_PROP(node_id, spi_cpha), SPI_MODE_CPHA, (0)) |   \
                        COND_CODE_1(DT_PROP(node_id, spi_hold_cs), SPI_HOLD_ON_CS, (0)),        \
                .slave = DT_REG_ADDR(node_id),                          \
                .cs = SPI_CS_CONTROL_INIT(node_id, delay_),             \
        }

Structure initializer for spi_config from devicetree.

This helper macro expands to a static initializer for a struct spi_config by reading the relevant frequency, slave, and cs data from the devicetree.

Parameters

node_id	Devicetree node identifier for the SPI device whose struct spi_config to create an initializer for
operation_	the desired operation field in the struct spi_config
delay_	the desired delay field in the struct spi_config's spi_cs_control, if there is one

SPI_CONFIG_DT_INST

#define SPI_CONFIG_DT_INST	(		inst,
			operation_,
			delay_ )

#include <zephyr/drivers/spi.h>

Value:

        SPI_CONFIG_DT(DT_DRV_INST(inst), operation_, delay_)

Structure initializer for spi_config from devicetree instance.

This is equivalent to SPI_CONFIG_DT(DT_DRV_INST(inst), operation_, delay_).

Parameters

inst	Devicetree instance number
operation_	the desired operation field in the struct spi_config
delay_	the desired delay field in the struct spi_config's spi_cs_control, if there is one

SPI_CS_ACTIVE_HIGH

#define SPI_CS_ACTIVE_HIGH   BIT(14)

#include <zephyr/drivers/spi.h>

Active high logic on CS.

Usually, and by default, CS logic is active low. However, some devices may require the reverse logic: active high. This bit will request the controller to use that logic. Note that not all controllers are able to handle that natively. In this case deferring the CS control to a gpio line through struct spi_cs_control would be the solution.

SPI_CS_CONTROL_INIT

#define SPI_CS_CONTROL_INIT	(		node_id,
			delay_ )

#include <zephyr/drivers/spi.h>

Value:

        {                                                         \
                .gpio = SPI_CS_GPIOS_DT_SPEC_GET(node_id),        \
                .delay = (delay_),                                \
        }

Initialize and get a pointer to a spi_cs_control from a devicetree node identifier.

This helper is useful for initializing a device on a SPI bus. It initializes a struct spi_cs_control and returns a pointer to it. Here, node_id is a node identifier for a SPI device, not a SPI controller.

Example devicetree fragment:

spi@abcd0001 {
        cs-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
        spidev: spi-device@0 { ... };
};

Example usage:

struct spi_cs_control ctrl =
        SPI_CS_CONTROL_INIT(DT_NODELABEL(spidev), 2);

This example is equivalent to:

struct spi_cs_control ctrl = {
        .gpio = SPI_CS_GPIOS_DT_SPEC_GET(DT_NODELABEL(spidev)),
        .delay = 2,
};

Parameters

node_id	Devicetree node identifier for a device on a SPI bus
delay_	The delay field to set in the spi_cs_control

Returns

a pointer to the spi_cs_control structure

SPI_CS_CONTROL_INIT_INST

#define SPI_CS_CONTROL_INIT_INST	(		inst,
			delay_ )

#include <zephyr/drivers/spi.h>

Value:

        SPI_CS_CONTROL_INIT(DT_DRV_INST(inst), delay_)

Get a pointer to a spi_cs_control from a devicetree node.

This is equivalent to SPI_CS_CONTROL_INIT(DT_DRV_INST(inst), delay).

Therefore, DT_DRV_COMPAT must already be defined before using this macro.

Parameters

inst	Devicetree node instance number
delay_	The delay field to set in the spi_cs_control

Returns

a pointer to the spi_cs_control structure

SPI_CS_GPIOS_DT_SPEC_GET

#define SPI_CS_GPIOS_DT_SPEC_GET

(

spi_dev

)

#include <zephyr/drivers/spi.h>

Value:

        GPIO_DT_SPEC_GET_BY_IDX_OR(DT_BUS(spi_dev), cs_gpios,   \
                                   DT_REG_ADDR(spi_dev), {})

Get a struct gpio_dt_spec for a SPI device's chip select pin.

Example devicetree fragment:

gpio1: gpio@abcd0001 { ... };
 
gpio2: gpio@abcd0002 { ... };
 
spi@abcd0003 {
        compatible = "vnd,spi";
        cs-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>,
                   <&gpio2 20 GPIO_ACTIVE_LOW>;
 
        a: spi-dev-a@0 {
                reg = <0>;
        };
 
        b: spi-dev-b@1 {
                reg = <1>;
        };
};

Example usage:

SPI_CS_GPIOS_DT_SPEC_GET(DT_NODELABEL(a)) \
      // { DEVICE_DT_GET(DT_NODELABEL(gpio1)), 10, GPIO_ACTIVE_LOW }
SPI_CS_GPIOS_DT_SPEC_GET(DT_NODELABEL(b)) \
      // { DEVICE_DT_GET(DT_NODELABEL(gpio2)), 20, GPIO_ACTIVE_LOW }

Parameters

spi_dev

a SPI device node identifier

Returns

gpio_dt_spec struct corresponding with spi_dev's chip select

SPI_CS_GPIOS_DT_SPEC_INST_GET

#define SPI_CS_GPIOS_DT_SPEC_INST_GET

(

inst

)

#include <zephyr/drivers/spi.h>

Value:

        SPI_CS_GPIOS_DT_SPEC_GET(DT_DRV_INST(inst))

Get a struct gpio_dt_spec for a SPI device's chip select pin.

This is equivalent to SPI_CS_GPIOS_DT_SPEC_GET(DT_DRV_INST(inst)).

Parameters

inst	Devicetree instance number

Returns

gpio_dt_spec struct corresponding with spi_dev's chip select

SPI_DEVICE_DT_DEFINE

#define SPI_DEVICE_DT_DEFINE	(		node_id,
			init_fn,
			pm,
			data,
			config,
			level,
			prio,
			api,
			... )

#include <zephyr/drivers/spi.h>

Value:

        Z_DEVICE_STATE_DEFINE(Z_DEVICE_DT_DEV_ID(node_id));                     \
        Z_DEVICE_DEFINE(node_id, Z_DEVICE_DT_DEV_ID(node_id),                   \
                        DEVICE_DT_NAME(node_id), init_fn, pm, data, config,     \
                        level, prio, api,                                       \
                        &Z_DEVICE_STATE_NAME(Z_DEVICE_DT_DEV_ID(node_id)),      \
                        __VA_ARGS__)

SPI_DT_IODEV_DEFINE

#define SPI_DT_IODEV_DEFINE	(		name,
			node_id,
			operation_,
			delay_ )

#include <zephyr/drivers/spi.h>

Value:

        const struct spi_dt_spec _spi_dt_spec_##name =                          \
                SPI_DT_SPEC_GET(node_id, operation_, delay_);                   \
        RTIO_IODEV_DEFINE(name, &spi_iodev_api, (void *)&_spi_dt_spec_##name)

Define an iodev for a given dt node on the bus.

These do not need to be shared globally but doing so will save a small amount of memory.

Parameters

name	Symbolic name to use for defining the iodev
node_id	Devicetree node identifier
operation_	SPI operational mode
delay_	Chip select delay in microseconds

SPI_DT_SPEC_GET

#define SPI_DT_SPEC_GET	(		node_id,
			operation_,
			delay_ )

#include <zephyr/drivers/spi.h>

Value:

        {                                                            \
                .bus = DEVICE_DT_GET(DT_BUS(node_id)),               \
                .config = SPI_CONFIG_DT(node_id, operation_, delay_) \
        }

Structure initializer for spi_dt_spec from devicetree.

This helper macro expands to a static initializer for a struct spi_dt_spec by reading the relevant bus, frequency, slave, and cs data from the devicetree.

Important: multiple fields are automatically constructed by this macro which must be checked before use. spi_is_ready_dt performs the required device_is_ready checks.

Parameters

node_id	Devicetree node identifier for the SPI device whose struct spi_dt_spec to create an initializer for
operation_	the desired operation field in the struct spi_config
delay_	the desired delay field in the struct spi_config's spi_cs_control, if there is one

SPI_DT_SPEC_INST_GET

#define SPI_DT_SPEC_INST_GET	(		inst,
			operation_,
			delay_ )

#include <zephyr/drivers/spi.h>

Value:

        SPI_DT_SPEC_GET(DT_DRV_INST(inst), operation_, delay_)

Structure initializer for spi_dt_spec from devicetree instance.

This is equivalent to SPI_DT_SPEC_GET(DT_DRV_INST(inst), operation_, delay_).

Parameters

inst	Devicetree instance number
operation_	the desired operation field in the struct spi_config
delay_	the desired delay field in the struct spi_config's spi_cs_control, if there is one

SPI_FRAME_FORMAT_MOTOROLA

#define SPI_FRAME_FORMAT_MOTOROLA   (0U << 15)

#include <zephyr/dt-bindings/spi/spi.h>

SPI_FRAME_FORMAT_TI

#define SPI_FRAME_FORMAT_TI   (1U << 15)

#include <zephyr/dt-bindings/spi/spi.h>

SPI_FULL_DUPLEX

#define SPI_FULL_DUPLEX   (0U << 11)

#include <zephyr/dt-bindings/spi/spi.h>

SPI_HALF_DUPLEX

#define SPI_HALF_DUPLEX   (1U << 11)

#include <zephyr/dt-bindings/spi/spi.h>

SPI_HOLD_ON_CS

#define SPI_HOLD_ON_CS   BIT(12)

#include <zephyr/drivers/spi.h>

Requests - if possible - to keep CS asserted after the transaction.

SPI_LINES_DUAL

#define SPI_LINES_DUAL   (1U << 16)

#include <zephyr/drivers/spi.h>

Dual lines.

SPI_LINES_MASK

#define SPI_LINES_MASK   (0x3U << 16)

#include <zephyr/drivers/spi.h>

Mask for MISO lines in spi_operation_t.

SPI_LINES_OCTAL

#define SPI_LINES_OCTAL   (3U << 16)

#include <zephyr/drivers/spi.h>

Octal lines.

SPI_LINES_QUAD

#define SPI_LINES_QUAD   (2U << 16)

#include <zephyr/drivers/spi.h>

Quad lines.

SPI_LINES_SINGLE

#define SPI_LINES_SINGLE   (0U << 16)

#include <zephyr/drivers/spi.h>

Single line.

SPI_LOCK_ON

#define SPI_LOCK_ON   BIT(13)

#include <zephyr/drivers/spi.h>

Keep the device locked after the transaction for the current config.

Use this with extreme caution (see spi_release() below) as it will prevent other callers to access the SPI device until spi_release() is properly called.

SPI_MODE_CPHA

#define SPI_MODE_CPHA   BIT(2)

#include <zephyr/drivers/spi.h>

Clock Phase: this dictates when is the data captured, and depends clock's polarity.

When SPI_MODE_CPOL is set and this bit as well, capture will occur on low to high transition and high to low if this bit is not set (default). This is fully reversed if CPOL is not set.

SPI_MODE_CPOL

#define SPI_MODE_CPOL   BIT(1)

#include <zephyr/drivers/spi.h>

Clock Polarity: if set, clock idle state will be 1 and active state will be 0.

If untouched, the inverse will be true which is the default.

SPI_MODE_GET

#define SPI_MODE_GET

(

_mode_

)

#include <zephyr/drivers/spi.h>

Value:

        ((_mode_) & SPI_MODE_MASK)

Get SPI polarity and phase mode bits.

SPI_MODE_LOOP

#define SPI_MODE_LOOP   BIT(3)

#include <zephyr/drivers/spi.h>

Whatever data is transmitted is looped-back to the receiving buffer of the controller.

This is fully controller dependent as some may not support this, and can be used for testing purposes only.

SPI_MOSI_OVERRUN_DT

#define SPI_MOSI_OVERRUN_DT

(

node_id

)

#include <zephyr/drivers/spi.h>

Value:

        DT_PROP_OR(node_id, overrun_character, SPI_MOSI_OVERRUN_UNKNOWN)

The value sent on MOSI when all TX bytes are sent, but RX continues.

For drivers where the MOSI line state when receiving is important, this value can be queried at compile-time to determine whether allocating a constant array is necessary.

Parameters

node_id

Devicetree node identifier for the SPI device to query

Return values

SPI_MOSI_OVERRUN_UNKNOWN	if controller does not export the value
byte	default MOSI value otherwise

SPI_MOSI_OVERRUN_DT_INST

#define SPI_MOSI_OVERRUN_DT_INST

(

inst

)

#include <zephyr/drivers/spi.h>

Value:

        DT_INST_PROP_OR(inst, overrun_character, SPI_MOSI_OVERRUN_UNKNOWN)

The value sent on MOSI when all TX bytes are sent, but RX continues.

This is equivalent to SPI_MOSI_OVERRUN_DT(DT_DRV_INST(inst)).

Parameters

inst	Devicetree instance number

Return values

SPI_MOSI_OVERRUN_UNKNOWN	if controller does not export the value
byte	default MOSI value otherwise

SPI_MOSI_OVERRUN_UNKNOWN

#define SPI_MOSI_OVERRUN_UNKNOWN   0x100

#include <zephyr/drivers/spi.h>

Value that will never compare true with any valid overrun character.

SPI_OP_MODE_GET

#define SPI_OP_MODE_GET

(

_operation_

)

#include <zephyr/drivers/spi.h>

Value:

((_operation_) & SPI_OP_MODE_MASK)

Get SPI operational mode.

SPI_OP_MODE_MASTER

#define SPI_OP_MODE_MASTER   0U

#include <zephyr/drivers/spi.h>

Master mode.

SPI_OP_MODE_SLAVE

#define SPI_OP_MODE_SLAVE   BIT(0)

#include <zephyr/drivers/spi.h>

Slave mode.

SPI_STATS_RX_BYTES_INC

#define SPI_STATS_RX_BYTES_INC

(

dev_

)

#include <zephyr/drivers/spi.h>

SPI_STATS_TRANSFER_ERROR_INC

#define SPI_STATS_TRANSFER_ERROR_INC

(

dev_

)

#include <zephyr/drivers/spi.h>

SPI_STATS_TX_BYTES_INC

#define SPI_STATS_TX_BYTES_INC

(

dev_

)

#include <zephyr/drivers/spi.h>

spi_transceive_stats

#define spi_transceive_stats	(		dev,
			error,
			tx_bufs,
			rx_bufs )

#include <zephyr/drivers/spi.h>

SPI_TRANSFER_LSB

#define SPI_TRANSFER_LSB   BIT(4)

#include <zephyr/drivers/spi.h>

Least significant bit first.

SPI_TRANSFER_MSB

#define SPI_TRANSFER_MSB   (0U)

#include <zephyr/drivers/spi.h>

Most significant bit first.

SPI_WORD_SET

#define SPI_WORD_SET

(

_word_size_

)

#include <zephyr/drivers/spi.h>

Value:

        ((_word_size_) << SPI_WORD_SIZE_SHIFT)

Set SPI word size.

SPI_WORD_SIZE_GET

#define SPI_WORD_SIZE_GET

(

_operation_

)

#include <zephyr/drivers/spi.h>

Value:

        (((_operation_) & SPI_WORD_SIZE_MASK) >> SPI_WORD_SIZE_SHIFT)

Get SPI word size.

Typedef Documentation

spi_api_io

typedef int(* spi_api_io) (const struct device *dev, const struct spi_config *config, const struct spi_buf_set *tx_bufs, const struct spi_buf_set *rx_bufs)

#include <zephyr/drivers/spi.h>

Callback API for I/O See spi_transceive() for argument descriptions.

Callback API for asynchronous I/O See spi_transceive_signal() for argument descriptions.

spi_api_io_async

typedef int(* spi_api_io_async) (const struct device *dev, const struct spi_config *config, const struct spi_buf_set *tx_bufs, const struct spi_buf_set *rx_bufs, spi_callback_t cb, void *userdata)

#include <zephyr/drivers/spi.h>

spi_api_release

typedef int(* spi_api_release) (const struct device *dev, const struct spi_config *config)

#include <zephyr/drivers/spi.h>

Callback API for unlocking SPI device.

See spi_release() for argument descriptions

spi_callback_t

typedef void(* spi_callback_t) (const struct device *dev, int result, void *data)

#include <zephyr/drivers/spi.h>

SPI callback for asynchronous transfer requests.

Parameters

dev	SPI device which is notifying of transfer completion or error
result	Result code of the transfer request. 0 is success, -errno for failure.
data	Transfer requester supplied data which is passed along to the callback.

spi_operation_t

typedef uint16_t spi_operation_t

#include <zephyr/drivers/spi.h>

Opaque type to hold the SPI operation flags.

Function Documentation

spi_cs_is_gpio()

static bool spi_cs_is_gpio ( const struct spi_config * config )

inlinestatic

#include <zephyr/drivers/spi.h>

Check if SPI CS is controlled using a GPIO.

Parameters

config

SPI configuration.

Returns

true If CS is controlled using a GPIO.

false If CS is controlled by hardware or any other means.

spi_cs_is_gpio_dt()

static bool spi_cs_is_gpio_dt ( const struct spi_dt_spec * spec )

inlinestatic

#include <zephyr/drivers/spi.h>

Check if SPI CS in spi_dt_spec is controlled using a GPIO.

Parameters

spec	SPI specification from devicetree.

Returns

true If CS is controlled using a GPIO.

false If CS is controlled by hardware or any other means.

spi_iodev_submit()

static void spi_iodev_submit ( struct rtio_iodev_sqe * iodev_sqe )

inlinestatic

#include <zephyr/drivers/spi.h>

Submit a SPI device with a request.

Parameters

iodev_sqe

Prepared submissions queue entry connected to an iodev defined by SPI_IODEV_DEFINE. Must live as long as the request is in flight.

spi_is_ready_dt()

static bool spi_is_ready_dt ( const struct spi_dt_spec * spec )

inlinestatic

#include <zephyr/drivers/spi.h>

Validate that SPI bus (and CS gpio if defined) is ready.

Parameters

spec	SPI specification from devicetree

Return values

true	if the SPI bus is ready for use.
false	if the SPI bus (or the CS gpio defined) is not ready for use.

spi_is_ready_iodev()

static bool spi_is_ready_iodev ( const struct rtio_iodev * spi_iodev )

inlinestatic

#include <zephyr/drivers/spi.h>

Validate that SPI bus (and CS gpio if defined) is ready.

Parameters

spi_iodev

SPI iodev defined with SPI_DT_IODEV_DEFINE

Return values

true	if the SPI bus is ready for use.
false	if the SPI bus (or the CS gpio defined) is not ready for use.

spi_read()

static int spi_read ( const struct device * dev, const struct spi_config * config, const struct spi_buf_set * rx_bufs )

inlinestatic

#include <zephyr/drivers/spi.h>

Read the specified amount of data from the SPI driver.

Note

This function is synchronous.

This function is a helper function calling spi_transceive.

Parameters

dev	Pointer to the device structure for the driver instance
config	Pointer to a valid spi_config structure instance. Pointer-comparison may be used to detect changes from previous operations.
rx_bufs	Buffer array where data to be read will be written to.

Return values

frames	Positive number of frames received in slave mode.
0	If successful.
-errno	Negative errno code on failure.

spi_read_dt()

static int spi_read_dt ( const struct spi_dt_spec * spec, const struct spi_buf_set * rx_bufs )

inlinestatic

#include <zephyr/drivers/spi.h>

Read data from a SPI bus specified in spi_dt_spec.

This is equivalent to:

spi_read(spec->bus, &spec->config, rx_bufs);

Parameters

spec	SPI specification from devicetree
rx_bufs	Buffer array where data to be read will be written to.

Returns

a value from spi_read().

spi_read_signal()

static int spi_read_signal ( const struct device * dev, const struct spi_config * config, const struct spi_buf_set * rx_bufs, struct k_poll_signal * sig )

inlinestatic

#include <zephyr/drivers/spi.h>

Read the specified amount of data from the SPI driver.

Note

This function is asynchronous.

This function is a helper function calling spi_transceive_signal.

This function is available only if

CONFIG_SPI_ASYNC 

and

CONFIG_POLL 

are selected.

Parameters

dev	Pointer to the device structure for the driver instance
config	Pointer to a valid spi_config structure instance. Pointer-comparison may be used to detect changes from previous operations.
rx_bufs	Buffer array where data to be read will be written to.
sig	A pointer to a valid and ready to be signaled struct k_poll_signal. (Note: if NULL this function will not notify the end of the transaction, and whether it went successfully or not).

Return values

frames	Positive number of frames received in slave mode.
0	If successful
-errno	Negative errno code on failure.

spi_release()

int spi_release	(	const struct device *	dev,
		const struct spi_config *	config )

#include <zephyr/drivers/spi.h>

Release the SPI device locked on and/or the CS by the current config.

Note: This synchronous function is used to release either the lock on the SPI device and/or the CS line that was kept if, and if only, given config parameter was the last one to be used (in any of the above functions) and if it has the SPI_LOCK_ON bit set and/or the SPI_HOLD_ON_CS bit set into its operation bits field. This can be used if the caller needs to keep its hand on the SPI device for consecutive transactions and/or if it needs the device to stay selected. Usually both bits will be used along each other, so the the device is locked and stays on until another operation is necessary or until it gets released with the present function.

Parameters

dev	Pointer to the device structure for the driver instance
config	Pointer to a valid spi_config structure instance.

Return values

0	If successful.
-errno	Negative errno code on failure.

spi_release_dt()

static int spi_release_dt ( const struct spi_dt_spec * spec )

inlinestatic

#include <zephyr/drivers/spi.h>

Release the SPI device specified in spi_dt_spec.

This is equivalent to:

spi_release(spec->bus, &spec->config);

Parameters

spec	SPI specification from devicetree

Returns

a value from spi_release().

spi_transceive()

int spi_transceive	(	const struct device *	dev,
		const struct spi_config *	config,
		const struct spi_buf_set *	tx_bufs,
		const struct spi_buf_set *	rx_bufs )

#include <zephyr/drivers/spi.h>

Read/write the specified amount of data from the SPI driver.

Note

This function is synchronous.

Parameters

dev	Pointer to the device structure for the driver instance
config	Pointer to a valid spi_config structure instance. Pointer-comparison may be used to detect changes from previous operations.
tx_bufs	Buffer array where data to be sent originates from, or NULL if none.
rx_bufs	Buffer array where data to be read will be written to, or NULL if none.

Return values

frames	Positive number of frames received in slave mode.
0	If successful in master mode.
-errno	Negative errno code on failure.

spi_transceive_cb()

static int spi_transceive_cb ( const struct device * dev, const struct spi_config * config, const struct spi_buf_set * tx_bufs, const struct spi_buf_set * rx_bufs, spi_callback_t callback, void * userdata )

inlinestatic

#include <zephyr/drivers/spi.h>

Read/write the specified amount of data from the SPI driver.

Note

This function is asynchronous.

This function is available only if

CONFIG_SPI_ASYNC 

is selected.

Parameters

dev	Pointer to the device structure for the driver instance
config	Pointer to a valid spi_config structure instance. Pointer-comparison may be used to detect changes from previous operations.
tx_bufs	Buffer array where data to be sent originates from, or NULL if none.
rx_bufs	Buffer array where data to be read will be written to, or NULL if none.
callback	Function pointer to completion callback. (Note: if NULL this function will not notify the end of the transaction, and whether it went successfully or not).
userdata	Userdata passed to callback

Return values

frames	Positive number of frames received in slave mode.
0	If successful in master mode.
-errno	Negative errno code on failure.

spi_transceive_dt()

static int spi_transceive_dt ( const struct spi_dt_spec * spec, const struct spi_buf_set * tx_bufs, const struct spi_buf_set * rx_bufs )

inlinestatic

#include <zephyr/drivers/spi.h>

Read/write data from an SPI bus specified in spi_dt_spec.

This is equivalent to:

spi_transceive(spec->bus, &spec->config, tx_bufs, rx_bufs);

Parameters

spec	SPI specification from devicetree
tx_bufs	Buffer array where data to be sent originates from, or NULL if none.
rx_bufs	Buffer array where data to be read will be written to, or NULL if none.

Returns

a value from spi_transceive().

spi_transceive_signal()

static int spi_transceive_signal ( const struct device * dev, const struct spi_config * config, const struct spi_buf_set * tx_bufs, const struct spi_buf_set * rx_bufs, struct k_poll_signal * sig )

inlinestatic

#include <zephyr/drivers/spi.h>

Read/write the specified amount of data from the SPI driver.

Note

This function is asynchronous.

This function is available only if

CONFIG_SPI_ASYNC 

and

CONFIG_POLL 

are selected.

Parameters

dev	Pointer to the device structure for the driver instance
config	Pointer to a valid spi_config structure instance. Pointer-comparison may be used to detect changes from previous operations.
tx_bufs	Buffer array where data to be sent originates from, or NULL if none.
rx_bufs	Buffer array where data to be read will be written to, or NULL if none.
sig	A pointer to a valid and ready to be signaled struct k_poll_signal. (Note: if NULL this function will not notify the end of the transaction, and whether it went successfully or not).

Return values

frames	Positive number of frames received in slave mode.
0	If successful in master mode.
-errno	Negative errno code on failure.

spi_write()

static int spi_write ( const struct device * dev, const struct spi_config * config, const struct spi_buf_set * tx_bufs )

inlinestatic

#include <zephyr/drivers/spi.h>

Write the specified amount of data from the SPI driver.

Note

This function is synchronous.

This function is a helper function calling spi_transceive.

Parameters

dev	Pointer to the device structure for the driver instance
config	Pointer to a valid spi_config structure instance. Pointer-comparison may be used to detect changes from previous operations.
tx_bufs	Buffer array where data to be sent originates from.

Return values

0	If successful.
-errno	Negative errno code on failure.

spi_write_dt()

static int spi_write_dt ( const struct spi_dt_spec * spec, const struct spi_buf_set * tx_bufs )

inlinestatic

#include <zephyr/drivers/spi.h>

Write data to a SPI bus specified in spi_dt_spec.

This is equivalent to:

spi_write(spec->bus, &spec->config, tx_bufs);

Parameters

spec	SPI specification from devicetree
tx_bufs	Buffer array where data to be sent originates from.

Returns

a value from spi_write().

spi_write_signal()

static int spi_write_signal ( const struct device * dev, const struct spi_config * config, const struct spi_buf_set * tx_bufs, struct k_poll_signal * sig )

inlinestatic

#include <zephyr/drivers/spi.h>

Write the specified amount of data from the SPI driver.

Note

This function is asynchronous.

This function is a helper function calling spi_transceive_signal.

This function is available only if

CONFIG_SPI_ASYNC 

and

CONFIG_POLL 

are selected.

Parameters

dev	Pointer to the device structure for the driver instance
config	Pointer to a valid spi_config structure instance. Pointer-comparison may be used to detect changes from previous operations.
tx_bufs	Buffer array where data to be sent originates from.
sig	A pointer to a valid and ready to be signaled struct k_poll_signal. (Note: if NULL this function will not notify the end of the transaction, and whether it went successfully or not).

Return values

0	If successful.
-errno	Negative errno code on failure.

Variable Documentation

spi_iodev_api

const struct rtio_iodev_api spi_iodev_api

extern

#include <zephyr/drivers/spi.h>