nordic,nrf7002-qspi (on qspi bus)

Description

This is a representation of the nRF7002 Wi-Fi chip with QSPI interface.

Properties

Properties not inherited from the base binding file.

Name	Type	Details
`iovdd-ctrl-gpios`	`phandle-array`	GPIO of the SoC controlling IO_VDD Control pin of the nRF70 This property is required.
`bucken-gpios`	`phandle-array`	GPIO of the SoC controlling BUCK_EN pin of the nRF70 This property is required.
`host-irq-gpios`	`phandle-array`	GPIO of the SoC controlling the HOST_IRQ pin of the nRF70 This property is required.
`srrf-switch-gpios`	`phandle-array`	GPIO of the RF Switch to control SR RF output to either SR Antenna or shared Antenna with Wi-Fi
`qspi-frequency`	`int`	Maximum clock speed (in Hz) supported by the device. This property is required.
`qspi-quad-mode`	`boolean`	If specified, Use QSPI in quad mode (4 IO lines) otherwise in SPI mode (2 IO lines - MOSI & MISO).
`qspi-rx-delay`	`int`	Number of clock cycles from the rising edge of the SPI clock until the input serial data is sampled.
`qspi-cpha`	`boolean`	Set to indicate phase starts with asserted half-phase (CPHA=1). The driver using this property must also use `cpol`.
`qspi-cpol`	`boolean`	Set to indicate that the clock leading edge is falling (CPOL=1). The driver using this property requires also use `cpha`.
`wifi-max-tx-pwr-2g-dsss`	`int`	Maximum transmit power allowed in 2.4GHz band for DSSS/CCK rates This property is required.
`wifi-max-tx-pwr-2g-mcs0`	`int`	Maximum transmit power allowed in 2.4GHz band for MCS0 This property is required.
`wifi-max-tx-pwr-2g-mcs7`	`int`	Maximum transmit power allowed in 2.4GHz band for MCS7 This property is required.
`wifi-max-tx-pwr-5g-low-mcs0`	`int`	Maximum transmit power allowed in 5GHz band MCS0 low sub-band This property is required.
`wifi-max-tx-pwr-5g-low-mcs7`	`int`	Maximum transmit power allowed in 5GHz band MCS7 low sub-band This property is required.
`wifi-max-tx-pwr-5g-mid-mcs0`	`int`	Maximum transmit power allowed in 5GHz band MCS0 mid sub-band This property is required.
`wifi-max-tx-pwr-5g-mid-mcs7`	`int`	Maximum transmit power allowed in 5GHz band MCS7 mid sub-band This property is required.
`wifi-max-tx-pwr-5g-high-mcs0`	`int`	Maximum transmit power allowed in 5GHz band MCS0 high sub-band This property is required.
`wifi-max-tx-pwr-5g-high-mcs7`	`int`	Maximum transmit power allowed in 5GHz band MCS7 high sub-band

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nordic,nrf7002-qspi” compatible.

Name	Type	Details
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg`	`array`	register space This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`power-domains`	`phandle-array`	Power domain specifiers
`power-domain-names`	`string-array`	Provided names of power domain specifiers
`#power-domain-cells`	`int`	Number of cells in power-domains property
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().