onnn,ncp5623 (on i2c bus)
Vendor: ON Semiconductor Corp.
Description
NCP5623 Triple Output I2C Controlled RGB LED driver
The LED_SHELL application can be used for testing
The following example defines a single RGB LED in the ncp5623 DT node
ncp5623c@39 {
compatible = "onnn,ncp5623";
reg = <0x39>;
led_0 {
label = "RGB LED";
index = <0>;
color-mapping =
<LED_COLOR_ID_RED>,
<LED_COLOR_ID_GREEN>,
<LED_COLOR_ID_BLUE>;
};
};
The following example defines three single-channel LEDs in the ncp5623 DT node
ncp5623c@39 {
compatible = "onnn,ncp5623";
reg = <0x39>;
led_0 {
label = "RED LED";
index = <0>;
color-mapping =
<LED_COLOR_ID_RED>;
};
led_1 {
label = "GREEN LED";
index = <1>;
color-mapping =
<LED_COLOR_ID_GREEN>;
};
led_2 {
label = "BLUE LED";
index = <2>;
color-mapping =
<LED_COLOR_ID_BLUE>;
};
};
Properties
Top level properties
These property descriptions apply to “onnn,ncp5623” nodes themselves. This page also describes child node properties in the following sections.
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
GPIO specifier that controls power to the device.
This property should be provided when the device has a dedicated
switch that controls power to the device. The supply state is
entirely the responsibility of the device driver.
Contrast with vin-supply.
|
|
|
Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.
This property should be provided when device power is supplied
by a shared regulator. The supply state is dependent on the
request status of all devices fed by the regulator.
Contrast with supply-gpios. If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.
|
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “onnn,ncp5623” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
device address on i2c bus
This property is required. See Important properties for more information. |
|
|
name of each register space
|
|
|
interrupts for device
See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
Human readable string describing the device (used as device_get_binding() argument)
See Important properties for more information. This property is deprecated. |
|
|
Clock gate information
|
|
|
name of each clock
|
|
|
number of address cells in reg property
|
|
|
number of size cells in reg property
|
|
|
DMA channels specifiers
|
|
|
Provided names of DMA channel specifiers
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Power domain specifiers
|
|
|
Provided names of power domain specifiers
|
|
|
Number of cells in power-domains property
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|
Child node properties
Name |
Type |
Details |
|---|---|---|
|
|
Human readable string describing the LED
This property is required. See Important properties for more information. |
|
|
Index of the LED on a controller. It can be used by drivers or
applications to map a logical LED to its real position on the
controller. For example, this allows to handle boards where the
LEDs in an array/strip are not wired following the LED order of
the controller.
This property is required. |
|
|
Channel to color mapping of a multicolor LED. If a LED supports
several colors, then the color-mapping property can be used to
describe how the hardware channels and the colors are mapped.
For example the channel to color mapping of RGB LEDs would be
color-mapping =
<LED_COLOR_ID_RED>,
<LED_COLOR_ID_GREEN>,
<LED_COLOR_ID_BLUE>;
This property is required. |