pixart,pat912x (on i2c bus)
Vendor: PixArt Imaging Inc.
Description
PAT9125EL Miniature Optical Navigation Chip
Properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
GPIO specifier that controls power to the device.
This property should be provided when the device has a dedicated
switch that controls power to the device. The supply state is
entirely the responsibility of the device driver.
Contrast with vin-supply.
|
|
|
Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.
This property should be provided when device power is supplied
by a shared regulator. The supply state is dependent on the
request status of all devices fed by the regulator.
Contrast with supply-gpios. If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.
|
|
|
GPIO connected to the motion pin, active low.
This property is required. |
|
|
The input code for the X axis to report for the device, typically any of
INPUT_REL_*. No report produced for the device X axis if unspecified.
|
|
|
The input code for the Y axis to report for the device, typically any of
INPUT_REL_*. No report produced for the device Y axis if unspecified.
|
|
|
CPI resolution for the X axis, range 0 to 1275, rounded down to the
closest supported value in increments of 5.
|
|
|
CPI resolution for the Y axis, range 0 to 1275, rounded down to the
closest supported value in increments of 5.
|
|
|
Invert X axis values.
|
|
|
Invert Y axis values.
|
|
|
Enable sleep1 mode.
|
|
|
Enable sleep2 mode, only valid if sleep1 is also enabled.
|
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “pixart,pat912x” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
device address on i2c bus
This property is required. See Important properties for more information. |
|
|
name of each register space
|
|
|
interrupts for device
See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
Human readable string describing the device (used as device_get_binding() argument)
See Important properties for more information. This property is deprecated. |
|
|
Clock gate information
|
|
|
name of each clock
|
|
|
number of address cells in reg property
|
|
|
number of size cells in reg property
|
|
|
DMA channels specifiers
|
|
|
Provided names of DMA channel specifiers
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Power domain specifiers
|
|
|
Provided names of power domain specifiers
|
|
|
Number of cells in power-domains property
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|