current-sense-amplifier

Description

When an io-channel measures the voltage over a current sense amplifier,
the interesting measurement is almost always the current through the
sense resistor, not the voltage over it. This binding describes such a current
sense circuit.

This is based on Linux, documentation:
  https://www.kernel.org/doc/Documentation/devicetree/bindings/iio/afe/current-sense-amplifier.yaml

Properties

Properties not inherited from the base binding file.

Name	Type	Details
`sense-resistor-micro-ohms`	`int`	Resistance of the shunt resistor in micro-ohms This property is required.
`sense-gain-mult`	`int`	Amplifier gain multiplier. The default is <1>. Default value: `1`
`sense-gain-div`	`int`	Amplifier gain divider. The default is <1>. Default value: `1`
`power-gpios`	`phandle-array`	Control power to the current amplifier. If present the corresponding GPIO must be set to an active level to enable the current amplifier.

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “current-sense-amplifier” compatible.

Name	Type	Details
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg`	`array`	register space See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	Channels available with this divider configuration. This property is required.
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`power-domains`	`phandle-array`	Power domain specifiers
`power-domain-names`	`string-array`	Provided names of power domain specifiers
`#power-domain-cells`	`int`	Number of cells in power-domains property
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().