nuvoton,npcx-i3c
Vendor: Nuvoton Technology Corporation
Description
These nodes are “[‘i3c’, ‘i2c’]” bus nodes.
Nuvoton I3C controller
Representation:
/* If CONFIG_I3C_NPCX is enabled, the suggested clock configuration is as follows: */
&pcc {
clock-frequency = <DT_FREQ_M(90)>; /* OFMCLK runs at 90MHz */
core-prescaler = <3>; /* CORE_CLK runs at 30MHz */
apb1-prescaler = <6>; /* APB1_CLK runs at 15MHz */
apb2-prescaler = <6>; /* APB2_CLK runs at 15MHz */
apb3-prescaler = <6>; /* APB3_CLK runs at 15MHz */
apb4-prescaler = <3>; /* APB4_CLK runs at 30MHz */
};
&rst {
status = "okay";
};
&i3c0 {
status = "okay";
/* I3C clock frequency suggestion = <PP_SCL, OD_SCL> */
* Full speed = <12500000, 4170000>
* Normal speed = <7500000, 1500000>
*/
i3c-scl-hz = <12500000>;
i3c-od-scl-hz = <4170000>;
};
Properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
Frequency of the SCL signal used for I3C transfers. When undefined,
use the controller default or as specified by the I3C specification.
|
|
|
Frequency of the SCL signal used for I2C transfers. When undefined
and there are I2C devices attached to the bus, look at the Legacy
Virtual Register (LVR) of all connected I2C devices to determine
the maximum allowed frequency.
|
|
|
Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.
|
|
|
Pin configuration/s for the second state. See pinctrl-0.
|
|
|
Pin configuration/s for the third state. See pinctrl-0.
|
|
|
Pin configuration/s for the fourth state. See pinctrl-0.
|
|
|
Pin configuration/s for the fifth state. See pinctrl-0.
|
|
|
Names for the provided states. The number of names needs to match the
number of states.
|
|
|
Reset information
This property is required. |
|
|
Name of each reset
|
|
|
Open Drain Frequency for the I3C controller. When undefined, use
the controller default or as specified by the I3C specification.
|
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nuvoton,npcx-i3c” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
register space
This property is required. See Important properties for more information. |
|
|
name of each register space
|
|
|
interrupts for device
This property is required. See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
Human readable string describing the device (used as device_get_binding() argument)
See Important properties for more information. This property is deprecated. |
|
|
Clock gate information
|
|
|
name of each clock
|
|
|
number of address cells in reg property
This property is required. Constant value: |
|
|
number of size cells in reg property
This property is required. |
|
|
DMA channels specifiers
|
|
|
Provided names of DMA channel specifiers
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Power domain specifiers
|
|
|
Provided names of power domain specifiers
|
|
|
Number of cells in power-domains property
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|