adi,sdp-120
Vendor: Analog Devices, Inc.
Description
GPIO pins exposed on a Analog devices SDP interface.
120-pin SDP interface:
1 VIN NC 120
2 NC NC 119
3 GND GND 118
4 GND GND 117
5 USB_VBUS VIO 116
6 GND GND 115
7 PAR_D23 PAR_D22 114
8 PAR_D21 PAR_D20 113
9 PAR_D19 PAR_D18 112
10 PAR_D17 PAR_D16 111
11 GND PAR_D15 110
12 PAR_D14 GND 109
13 PAR_D13 PAR_D12 108
14 PAR_D11 PAR_D10 107
15 PAR_D9 PAR_D8 106
16 PAR_D7 PAR_D6 105
17 GND GND 104
18 PAR_D5 PAR_D4 103
19 PAR_D3 PAR_D2 102
20 PAR_D1 PAR_D0 101
21 PAR_RD_N PAR_WR_N 100
22 PAR_CS_N PAR_INT 99
23 GND GND 98
24 PAR_A3 PAR_A2 97
25 PAR_A1 PAR_A0 96
26 PAR_FS3 PAR_FS2 95
27 PAR_FS1 PAR_CLK 94
28 GND GND 93
29 SPORT_TDV0 SPORT_RSCLK 92
30 SPORT_TDV1 SPORT_DR0 91
31 SPORT_DR1 SPORT_RFS 90
32 SPORT_DT1 SPORT_TFS 89
33 SPI_D2 SPORT_DT0 88
34 SPI_D3 SPORT_TSCLK 87
35 SERIAL_INT GND 86
36 GND SPI_SEL_A_N 85
37 SPI_SEL_B_N SPI_MOSI 84
38 SPI_SEL_C_N SPI_MISO 83
39 SPI_SEL1/SPI_SS_N SPI_CLK 82
40 GND GND 81
41 SDA_1 SDA_0 80
42 SCL_1 SCL_0 79
43 GPIO0 GPIO1 78
44 GPIO2 GPIO3 77
45 GPIO4 GPIO5 76
46 GND GND 75
47 GPIO6 GPIO7 74
48 TMR_A TMR_B 73
49 TMR_C TMR_D 72
50 NC CLKOUT 71
51 NC NC 70
52 GND GND 69
53 NC NC 68
54 NC NC 67
55 NC NC 66
56 EEPROM_A0 WAKE_N 65
57 RESET_OUT_N SLEEP_N 64
58 GND GND 63
59 UART_RX UART_TX 62
60 RESET_IN_N BMODE1 61
Properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
This property is required. |
|
|
|
|
|
|
|
|
Number of items to expect in a GPIO specifier
This property is required. |
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “adi,sdp-120” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
register space
See Important properties for more information. |
|
|
name of each register space
|
|
|
interrupts for device
See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
Human readable string describing the device (used as device_get_binding() argument)
See Important properties for more information. This property is deprecated. |
|
|
Clock gate information
|
|
|
name of each clock
|
|
|
number of address cells in reg property
|
|
|
number of size cells in reg property
|
|
|
DMA channels specifiers
|
|
|
Provided names of DMA channel specifiers
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Power domain specifiers
|
|
|
Provided names of power domain specifiers
|
|
|
Number of cells in power-domains property
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|