nuvoton,npcx-espi-taf
Vendor: Nuvoton Technology Corporation
Description
These nodes are “espi” bus nodes.
The target flash devices accessed by Nuvoton eSPI TAF controller.
Representation:
espi_taf: espitaf@4000a000 {
compatible = "nuvoton,npcx-espi-taf";
reg = <0x4000a000 0x2000>;
mapped-addr = <0x68000000>;
max-read-sz = "NPCX_ESPI_TAF_MAX_READ_REQ_64B";
erase-sz = "NPCX_ESPI_TAF_ERASE_BLOCK_SIZE_4KB";
#address-cells = <1>;
#size-cells = <1>;
status = "okay";
};
Properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.
|
|
|
Pin configuration/s for the second state. See pinctrl-0.
|
|
|
Pin configuration/s for the third state. See pinctrl-0.
|
|
|
Pin configuration/s for the fourth state. See pinctrl-0.
|
|
|
Pin configuration/s for the fifth state. See pinctrl-0.
|
|
|
Names for the provided states. The number of names needs to match the
number of states.
|
|
|
Mapped memory address of direct read access for flash.
This property is required. |
|
|
Erase block size of target flash. The default was 4KB Erase Block Size.
All Intel platforms require support for at least 4 KB Erase Block Size.
This property is required. Default value: Legal values: |
|
|
Maximum read request size of flash access channel. The default was 64 bytes.
This value is recommended in datasheet.
This property is required. Default value: Legal values: |
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nuvoton,npcx-espi-taf” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
register space
See Important properties for more information. |
|
|
name of each register space
|
|
|
interrupts for device
See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
Human readable string describing the device (used as device_get_binding() argument)
See Important properties for more information. This property is deprecated. |
|
|
Clock gate information
|
|
|
name of each clock
|
|
|
number of address cells in reg property
|
|
|
number of size cells in reg property
|
|
|
DMA channels specifiers
|
|
|
Provided names of DMA channel specifiers
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Power domain specifiers
|
|
|
Provided names of power domain specifiers
|
|
|
Number of cells in power-domains property
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|