ti,lmp90078 (on spi bus)

Vendor: Texas Instruments

Description

These nodes are “lmp90xxx” bus nodes.

Texas Instruments LMP90078 AFE binding

Properties

Top level properties

These property descriptions apply to “ti,lmp90078” nodes themselves. This page also describes child node properties in the following sections.

Node specific propertiesDeprecated node specific propertiesBase properties

Properties not inherited from the base binding file.

Name	Type	Details
#io-channel-cells	int	This property is required. Constant value: 1
supply-gpios	phandle-array	GPIO specifier that controls power to the device. This property should be provided when the device has a dedicated switch that controls power to the device. The supply state is entirely the responsibility of the device driver. Contrast with vin-supply.
vin-supply	phandle	Reference to the regulator that controls power to the device. The referenced devicetree node must have a regulator compatible. This property should be provided when device power is supplied by a shared regulator. The supply state is dependent on the request status of all devices fed by the regulator. Contrast with supply-gpios. If both properties are provided then the regulator must be requested before the supply GPIOS is set to an active state, and the supply GPIOS must be set to an inactive state before releasing the regulator.
spi-max-frequency	int	Maximum clock frequency of device's SPI interface in Hz This property is required.
duplex	int	Duplex mode, full or half. By default it's always full duplex thus 0 as this is, by far, the most common mode. Use the macros not the actual enum value, here is the concordance list (see dt-bindings/spi/spi.h) 0 SPI_FULL_DUPLEX 2048 SPI_HALF_DUPLEX Legal values: 0, 2048
frame-format	int	Motorola or TI frame format. By default it's always Motorola's, thus 0 as this is, by far, the most common format. Use the macros not the actual enum value, here is the concordance list (see dt-bindings/spi/spi.h) 0 SPI_FRAME_FORMAT_MOTOROLA 32768 SPI_FRAME_FORMAT_TI Legal values: 0, 32768
spi-cpol	boolean	SPI clock polarity which indicates the clock idle state. If it is used, the clock idle state is logic high; otherwise, low.
spi-cpha	boolean	SPI clock phase that indicates on which edge data is sampled. If it is used, data is sampled on the second edge; otherwise, on the first edge.
spi-hold-cs	boolean	In some cases, it is necessary for the master to manage SPI chip select under software control, so that multiple spi transactions can be performed without releasing it. A typical use case is variable length SPI packets where the first spi transaction reads the length and the second spi transaction reads length bytes.
drdyb-gpios	phandle-array	Data Ready Bar
rtd-current	int	RTD current in microampere

Child node properties

Name	Type	Details
reg	array	Channel identifier. This property is required. See Important properties for more information.
zephyr,gain	string	Gain selection: - ADC_GAIN_1_6: x 1/6 - ADC_GAIN_1_5: x 1/5 - ADC_GAIN_1_4: x 1/4 - ADC_GAIN_1_3: x 1/3 - ADC_GAIN_2_5: x 2/5 - ADC_GAIN_1_2: x 1/2 - ADC_GAIN_2_3: x 2/3 - ADC_GAIN_4_5: x 4/5 - ADC_GAIN_1: x 1 - ADC_GAIN_2: x 2 - ADC_GAIN_3: x 3 - ADC_GAIN_4: x 4 - ADC_GAIN_6: x 6 - ADC_GAIN_8: x 8 - ADC_GAIN_12: x 12 - ADC_GAIN_16: x 16 - ADC_GAIN_24: x 24 - ADC_GAIN_32: x 32 - ADC_GAIN_64: x 64 - ADC_GAIN_128: x 128 This property is required. Legal values: 'ADC_GAIN_1_6', 'ADC_GAIN_1_5', 'ADC_GAIN_1_4', 'ADC_GAIN_1_3', 'ADC_GAIN_2_5', 'ADC_GAIN_1_2', 'ADC_GAIN_2_3', 'ADC_GAIN_4_5', 'ADC_GAIN_1', 'ADC_GAIN_2', 'ADC_GAIN_3', 'ADC_GAIN_4', 'ADC_GAIN_6', 'ADC_GAIN_8', 'ADC_GAIN_12', 'ADC_GAIN_16', 'ADC_GAIN_24', 'ADC_GAIN_32', 'ADC_GAIN_64', 'ADC_GAIN_128'
zephyr,reference	string	Reference selection: - ADC_REF_VDD_1: VDD - ADC_REF_VDD_1_2: VDD/2 - ADC_REF_VDD_1_3: VDD/3 - ADC_REF_VDD_1_4: VDD/4 - ADC_REF_INTERNAL: Internal - ADC_REF_EXTERNAL0: External, input 0 - ADC_REF_EXTERNAL1: External, input 1 This property is required. Legal values: 'ADC_REF_VDD_1', 'ADC_REF_VDD_1_2', 'ADC_REF_VDD_1_3', 'ADC_REF_VDD_1_4', 'ADC_REF_INTERNAL', 'ADC_REF_EXTERNAL0', 'ADC_REF_EXTERNAL1'
zephyr,vref-mv	int	This property can be used to specify the voltage (in millivolts) of the reference selected for this channel, so that applications can get that value if needed for some calculations. For the internal reference, the voltage can be usually obtained with a dedicated ADC API call, so there is no need to use this property in that case, but for other references this property can be useful.
zephyr,acquisition-time	int	Acquisition time. Use the ADC_ACQ_TIME macro to compose the value for this property or pass ADC_ACQ_TIME_DEFAULT to use the default setting for a given hardware (e.g. when the hardware does not allow to configure the acquisition time). This property is required.
zephyr,differential	boolean	When set, selects differential input mode for the channel. Otherwise, single-ended mode is used unless the zephyr,input-negative property is specified, in which case the differential mode is selected implicitly.
zephyr,input-positive	int	Positive ADC input. Used only for drivers that select the ADC_CONFIGURABLE_INPUTS Kconfig option.
zephyr,input-negative	int	Negative ADC input. Used only for drivers that select the ADC_CONFIGURABLE_INPUTS Kconfig option. When specified, implies the differential input mode for the channel.
zephyr,resolution	int	ADC resolution to be used for the channel.
zephyr,oversampling	int	Oversampling setting to be used for the channel. When specified, each sample is averaged from 2^N conversion results (where N is the provided value).
zephyr,current-source-pin	uint8-array	Output pin selection for the current sources. The actual interpretation depends on the driver. This is used only for drivers which select the ADC_CONFIGURABLE_EXCITATION_CURRENT_SOURCE_PIN Kconfig option.
zephyr,vbias-pins	int	Output pin selection for the bias voltage. The actual interpretation depends on the driver. This is used only for drivers which select the ADC_CONFIGURABLE_VBIAS_PIN Kconfig option.

Specifier cell names

• io-channel cells: input