gic.h

Go to the documentation of this file.

/*
 * Copyright (c) 2019 Stephanos Ioannidis <[email protected]>
 *
 * SPDX-License-Identifier: Apache-2.0
 */
 
#ifndef ZEPHYR_INCLUDE_DRIVERS_GIC_H_
#define ZEPHYR_INCLUDE_DRIVERS_GIC_H_
 
/*
 * GIC Register Interface Base Addresses
 */
 
#define GIC_DIST_BASE   DT_REG_ADDR_BY_IDX(DT_INST(0, arm_gic), 0)
#define GIC_CPU_BASE    DT_REG_ADDR_BY_IDX(DT_INST(0, arm_gic), 1)
 
/*
 * GIC Distributor Interface
 */
 
/*
 * 0x000  Distributor Control Register
 * v1           ICDDCR
 * v2/v3        GICD_CTLR
 */
#define GICD_CTLR               (GIC_DIST_BASE +   0x0)
 
/*
 * 0x004  Interrupt Controller Type Register
 * v1           ICDICTR
 * v2/v3        GICD_TYPER
 */
#define GICD_TYPER              (GIC_DIST_BASE +   0x4)
 
/*
 * 0x008  Distributor Implementer Identification Register
 * v1           ICDIIDR
 * v2/v3        GICD_IIDR
 */
#define GICD_IIDR               (GIC_DIST_BASE +   0x8)
 
/*
 * 0x080  Interrupt Group Registers
 * v1           ICDISRn
 * v2/v3        GICD_IGROUPRn
 */
#define GICD_IGROUPRn           (GIC_DIST_BASE +  0x80)
 
/*
 * 0x100  Interrupt Set-Enable Registers
 * v1           ICDISERn
 * v2/v3        GICD_ISENABLERn
 */
#define GICD_ISENABLERn         (GIC_DIST_BASE + 0x100)
 
/*
 * 0x180  Interrupt Clear-Enable Registers
 * v1           ICDICERn
 * v2/v3        GICD_ICENABLERn
 */
#define GICD_ICENABLERn         (GIC_DIST_BASE + 0x180)
 
/*
 * 0x200  Interrupt Set-Pending Registers
 * v1           ICDISPRn
 * v2/v3        GICD_ISPENDRn
 */
#define GICD_ISPENDRn           (GIC_DIST_BASE + 0x200)
 
/*
 * 0x280  Interrupt Clear-Pending Registers
 * v1           ICDICPRn
 * v2/v3        GICD_ICPENDRn
 */
#define GICD_ICPENDRn           (GIC_DIST_BASE + 0x280)
 
/*
 * 0x300  Interrupt Set-Active Registers
 * v1           ICDABRn
 * v2/v3        GICD_ISACTIVERn
 */
#define GICD_ISACTIVERn         (GIC_DIST_BASE + 0x300)
 
#if CONFIG_GIC_VER >= 2
/*
 * 0x380  Interrupt Clear-Active Registers
 * v2/v3        GICD_ICACTIVERn
 */
#define GICD_ICACTIVERn         (GIC_DIST_BASE + 0x380)
#endif
 
/*
 * 0x400  Interrupt Priority Registers
 * v1           ICDIPRn
 * v2/v3        GICD_IPRIORITYRn
 */
#define GICD_IPRIORITYRn        (GIC_DIST_BASE + 0x400)
 
/*
 * 0x800  Interrupt Processor Targets Registers
 * v1           ICDIPTRn
 * v2/v3        GICD_ITARGETSRn
 */
#define GICD_ITARGETSRn         (GIC_DIST_BASE + 0x800)
 
/*
 * 0xC00  Interrupt Configuration Registers
 * v1           ICDICRn
 * v2/v3        GICD_ICFGRn
 */
#define GICD_ICFGRn             (GIC_DIST_BASE + 0xc00)
 
/*
 * 0xF00  Software Generated Interrupt Register
 * v1           ICDSGIR
 * v2/v3        GICD_SGIR
 */
#define GICD_SGIR               (GIC_DIST_BASE + 0xf00)
 
/*
 * GIC CPU Interface
 */
 
#if CONFIG_GIC_VER <= 2
 
/*
 * 0x0000  CPU Interface Control Register
 * v1           ICCICR
 * v2/v3        GICC_CTLR
 */
#define GICC_CTLR               (GIC_CPU_BASE +    0x0)
 
/*
 * 0x0004  Interrupt Priority Mask Register
 * v1           ICCPMR
 * v2/v3        GICC_PMR
 */
#define GICC_PMR                (GIC_CPU_BASE +    0x4)
 
/*
 * 0x0008  Binary Point Register
 * v1           ICCBPR
 * v2/v3        GICC_BPR
 */
#define GICC_BPR                (GIC_CPU_BASE +    0x8)
 
/*
 * 0x000C  Interrupt Acknowledge Register
 * v1           ICCIAR
 * v2/v3        GICC_IAR
 */
#define GICC_IAR                (GIC_CPU_BASE +    0xc)
 
/*
 * 0x0010  End of Interrupt Register
 * v1           ICCEOIR
 * v2/v3        GICC_EOIR
 */
#define GICC_EOIR               (GIC_CPU_BASE +   0x10)
 
 
/*
 * Helper Constants
 */
 
/* GICC_CTLR */
#define GICC_CTLR_ENABLEGRP0    BIT(0)
#define GICC_CTLR_ENABLEGRP1    BIT(1)
 
#define GICC_CTLR_ENABLE_MASK   (GICC_CTLR_ENABLEGRP0 | GICC_CTLR_ENABLEGRP1)
 
#if defined(CONFIG_GIC_V2)
 
#define GICC_CTLR_FIQBYPDISGRP0 BIT(5)
#define GICC_CTLR_IRQBYPDISGRP0 BIT(6)
#define GICC_CTLR_FIQBYPDISGRP1 BIT(7)
#define GICC_CTLR_IRQBYPDISGRP1 BIT(8)
 
#define GICC_CTLR_BYPASS_MASK   (GICC_CTLR_FIQBYPDISGRP0 | \
                                 GICC_CTLR_IRQBYPDISGRP1 | \
                                 GICC_CTLR_FIQBYPDISGRP1 | \
                                 GICC_CTLR_IRQBYPDISGRP1)
 
#endif /* CONFIG_GIC_V2 */
 
/* GICD_SGIR */
#define GICD_SGIR_TGTFILT(x)            ((x) << 24)
#define GICD_SGIR_TGTFILT_CPULIST       GICD_SGIR_TGTFILT(0b00)
#define GICD_SGIR_TGTFILT_ALLBUTREQ     GICD_SGIR_TGTFILT(0b01)
#define GICD_SGIR_TGTFILT_REQONLY       GICD_SGIR_TGTFILT(0b10)
 
#define GICD_SGIR_CPULIST(x)            ((x) << 16)
#define GICD_SGIR_CPULIST_CPU(n)        GICD_SGIR_CPULIST(BIT(n))
#define GICD_SGIR_CPULIST_MASK          0xff
 
#define GICD_SGIR_NSATT                 BIT(15)
 
#define GICD_SGIR_SGIINTID(x)           (x)
 
#endif /* CONFIG_GIC_VER <= 2 */
 
 
/* GICD_ICFGR */
#define GICD_ICFGR_MASK                 BIT_MASK(2)
#define GICD_ICFGR_TYPE                 BIT(1)
 
/* GICD_TYPER.ITLinesNumber 0:4 */
#define GICD_TYPER_ITLINESNUM_MASK      0x1f
 
/* GICD_TYPER.IDbits */
#define GICD_TYPER_IDBITS(typer)        ((((typer) >> 19) & 0x1f) + 1)
 
/*
 * Common Helper Constants
 */
#define GIC_SGI_INT_BASE                0
#define GIC_PPI_INT_BASE                16
 
#define GIC_IS_SGI(intid)               (((intid) >= GIC_SGI_INT_BASE) && \
                                         ((intid) < GIC_PPI_INT_BASE))
 
 
#define GIC_SPI_INT_BASE                32
 
#define GIC_SPI_MAX_INTID               1019
 
#define GIC_IS_SPI(intid)               (((intid) >= GIC_SPI_INT_BASE) && \
                                        ((intid) <= GIC_SPI_MAX_INTID))
 
#define GIC_NUM_INTR_PER_REG            32
 
#define GIC_NUM_CFG_PER_REG             16
 
#define GIC_NUM_PRI_PER_REG             4
 
/* GIC idle priority : value '0xff' will allow all interrupts */
#define GIC_IDLE_PRIO                   0xff
 
/* Priority levels 0:255 */
#define GIC_PRI_MASK                    0xff
 
/*
 * '0xa0'is used to initialize each interrupt default priority.
 * This is an arbitrary value in current context.
 * Any value '0x80' to '0xff' will work for both NS and S state.
 * The values of individual interrupt and default has to be chosen
 * carefully if PMR and BPR based nesting and preemption has to be done.
 */
#define GIC_INT_DEF_PRI_X4              0xa0a0a0a0
 
/* GIC special interrupt id */
#define GIC_INTID_SPURIOUS              1023
 
/* Fixme: update from platform specific define or dt */
#define GIC_NUM_CPU_IF                  CONFIG_MP_MAX_NUM_CPUS
 
#ifndef _ASMLANGUAGE
 
#include <zephyr/types.h>
#include <zephyr/device.h>
 
/*
 * GIC Driver Interface Functions
 */
 
void arm_gic_irq_enable(unsigned int irq);
 
void arm_gic_irq_disable(unsigned int irq);
 
bool arm_gic_irq_is_enabled(unsigned int irq);
 
bool arm_gic_irq_is_pending(unsigned int irq);
 
void arm_gic_irq_clear_pending(unsigned int irq);
 
void arm_gic_irq_set_priority(
        unsigned int irq, unsigned int prio, unsigned int flags);
 
unsigned int arm_gic_get_active(void);
 
void arm_gic_eoi(unsigned int irq);
 
#ifdef CONFIG_SMP
void arm_gic_secondary_init(void);
#endif
 
void gic_raise_sgi(unsigned int sgi_id, uint64_t target_aff,
                   uint16_t target_list);
 
#endif /* !_ASMLANGUAGE */
 
#endif /* ZEPHYR_INCLUDE_DRIVERS_GIC_H_ */