Network Configuration Guide
This document describes how various network configuration options can be set according to available resources in the system.
Network Buffer Configuration Options
The network buffer configuration options control how much data we are able to either send or receive at the same time.
CONFIG_NET_PKT_RX_COUNTMaximum amount of network packets we can receive at the same time.
CONFIG_NET_PKT_TX_COUNTMaximum amount of network packet sends pending at the same time.
CONFIG_NET_BUF_RX_COUNTHow many network buffers are allocated for receiving data. Each net_buf contains a small header and either a fixed or variable length data buffer. The
CONFIG_NET_BUF_DATA_SIZEis used whenCONFIG_NET_BUF_FIXED_DATA_SIZEis set. This is the default setting. The default size of the buffer is 128 bytes.The
CONFIG_NET_BUF_VARIABLE_DATA_SIZEis an experimental setting. There each net_buf data portion is allocated from a memory pool and can be the amount of data we have received from the network. When data is received from the network, it is placed into net_buf data portion. Depending on device resources and desired network usage, user can tweak the size of the fixed buffer by settingCONFIG_NET_BUF_DATA_SIZE, and the size of the data pool size by settingCONFIG_NET_PKT_BUF_RX_DATA_POOL_SIZEandCONFIG_NET_PKT_BUF_TX_DATA_POOL_SIZEif variable size buffers are used.When using the fixed size data buffers, the memory consumption of network buffers can be tweaked by selecting the size of the data part according to what kind of network data we are receiving. If one sets the data size to 256, but only receives packets that are 32 bytes long, then we are “wasting” 224 bytes for each packet because we cannot utilize the remaining data. One should not set the data size too low because there is some overhead involved for each net_buf. For these reasons the default network buffer size is set to 128 bytes.
The variable size data buffer feature is marked as experimental as it has not received as much testing as the fixed size buffers. Using variable size data buffers tries to improve memory utilization by allocating minimum amount of data we need for the network data. The extra cost here is the amount of time that is needed when dynamically allocating the buffer from the memory pool.
For example, in Ethernet the maximum transmission unit (MTU) size is 1500 bytes. If one wants to receive two full frames, then the net_pkt RX count should be set to 2, and net_buf RX count to (1500 / 128) * 2 which is 24. If TCP is being used, then these values need to be higher because we can queue the packets internally before delivering to the application.
CONFIG_NET_BUF_TX_COUNTHow many network buffers are allocated for sending data. This is similar setting as the receive buffer count but for sending.
Connection Options
CONFIG_NET_MAX_CONNThis option tells how many network connection endpoints are supported. For example each TCP connection requires one connection endpoint. Similarly each listening UDP connection requires one connection endpoint. Also various system services like DHCP and DNS need connection endpoints to work. The network shell command net conn can be used at runtime to see the network connection information.
CONFIG_NET_MAX_CONTEXTSNumber of network contexts to allocate. Each network context describes a network 5-tuple that is used when listening or sending network traffic. Each BSD socket in the system uses one network context.
Socket Options
CONFIG_NET_SOCKETS_POLL_MAXMaximum number of supported poll() entries. One needs to select proper value here depending on how many BSD sockets are polled in the system.
CONFIG_POSIX_MAX_FDSMaximum number of open file descriptors, this includes files, sockets, special devices, etc. One needs to select proper value here depending on how many BSD sockets are created in the system.
CONFIG_NET_SOCKETPAIR_BUFFER_SIZEThis option is used by socketpair() function. It sets the size of the internal intermediate buffer, in bytes. This sets the limit how large messages can be passed between two socketpair endpoints.
TLS Options
CONFIG_NET_SOCKETS_TLS_MAX_CONTEXTSMaximum number of TLS/DTLS contexts. Each TLS/DTLS connection needs one context.
CONFIG_NET_SOCKETS_TLS_MAX_CREDENTIALSThis variable sets maximum number of TLS/DTLS credentials that can be used with a specific socket.
CONFIG_NET_SOCKETS_TLS_MAX_CIPHERSUITESMaximum number of TLS/DTLS ciphersuites per socket. This variable sets maximum number of TLS/DTLS ciphersuites that can be used with specific socket, if set explicitly by socket option. By default, all ciphersuites that are available in the system are available to the socket.
CONFIG_NET_SOCKETS_TLS_MAX_APP_PROTOCOLSMaximum number of supported application layer protocols. This variable sets maximum number of supported application layer protocols over TLS/DTLS that can be set explicitly by a socket option. By default, no supported application layer protocol is set.
CONFIG_NET_SOCKETS_TLS_MAX_CLIENT_SESSION_COUNTThis variable specifies maximum number of stored TLS/DTLS sessions, used for TLS/DTLS session resumption.
CONFIG_TLS_MAX_CREDENTIALS_NUMBERMaximum number of TLS credentials that can be registered. Make sure that this value is high enough so that all the certificates can be loaded to the store.
IPv4/6 Options
CONFIG_NET_IF_MAX_IPV4_COUNTMaximum number of IPv4 network interfaces in the system. This tells how many network interfaces there will be in the system that will have IPv4 enabled. For example if you have two network interfaces, but only one of them can use IPv4 addresses, then this value can be set to 1. If both network interface could use IPv4, then the setting should be set to 2.
CONFIG_NET_IF_MAX_IPV6_COUNTMaximum number of IPv6 network interfaces in the system. This is similar setting as the IPv4 count option but for IPv6.
TCP Options
CONFIG_NET_TCP_TIME_WAIT_DELAYHow long to wait in TCP TIME_WAIT state (in milliseconds). To avoid a (low-probability) issue when delayed packets from previous connection get delivered to next connection reusing the same local/remote ports, RFC 793 (TCP) suggests to keep an old, closed connection in a special TIME_WAIT state for the duration of 2*MSL (Maximum Segment Lifetime). The RFC suggests to use MSL of 2 minutes, but notes
This is an engineering choice, and may be changed if experience indicates it is desirable to do so.
For low-resource systems, having large MSL may lead to quick resource exhaustion (and related DoS attacks). At the same time, the issue of packet misdelivery is largely alleviated in the modern TCP stacks by using random, non-repeating port numbers and initial sequence numbers. Due to this, Zephyr uses much lower value of 1500ms by default. Value of 0 disables TIME_WAIT state completely.
CONFIG_NET_TCP_RETRY_COUNTMaximum number of TCP segment retransmissions. The following formula can be used to determine the time (in ms) that a segment will be be buffered awaiting retransmission:
\[\sum_{n=0}^{\mathtt{NET\_TCP\_RETRY\_COUNT}} \bigg(1 \ll n\bigg)\times \mathtt{NET\_TCP\_INIT\_RETRANSMISSION\_TIMEOUT}\]With the default value of 9, the IP stack will try to retransmit for up to 1:42 minutes. This is as close as possible to the minimum value recommended by RFC 1122 (1:40 minutes). Only 5 bits are dedicated for the retransmission count, so accepted values are in the 0-31 range. It’s highly recommended to not go below 9, though.
Should a retransmission timeout occur, the receive callback is called with
-ETIMEDOUTerror code and the context is dereferenced.CONFIG_NET_TCP_MAX_SEND_WINDOW_SIZEMaximum sending window size to use. This value affects how the TCP selects the maximum sending window size. The default value 0 lets the TCP stack select the value according to amount of network buffers configured in the system. Note that if there are multiple active TCP connections in the system, then this value might require finetuning (lowering), otherwise multiple TCP connections could easily exhaust net_buf pool for the queued TX data.
CONFIG_NET_TCP_MAX_RECV_WINDOW_SIZEMaximum receive window size to use. This value defines the maximum TCP receive window size. Increasing this value can improve connection throughput, but requires more receive buffers available in the system for efficient operation. The default value 0 lets the TCP stack select the value according to amount of network buffers configured in the system.
CONFIG_NET_TCP_RECV_QUEUE_TIMEOUTHow long to queue received data (in ms). If we receive out-of-order TCP data, we queue it. This value tells how long the data is kept before it is discarded if we have not been able to pass the data to the application. If set to 0, then receive queueing is not enabled. The value is in milliseconds.
Note that we only queue data sequentially in current version i.e., there should be no holes in the queue. For example, if we receive SEQs 5,4,3,6 and are waiting SEQ 2, the data in segments 3,4,5,6 is queued (in this order), and then given to application when we receive SEQ 2. But if we receive SEQs 5,4,3,7 then the SEQ 7 is discarded because the list would not be sequential as number 6 is be missing.
Traffic Class Options
It is possible to configure multiple traffic classes (queues) when receiving
or sending network data. Each traffic class queue is implemented as a thread
with different priority. This means that higher priority network packet can
be placed to a higher priority network queue in order to send or receive it
faster or slower. Because of thread scheduling latencies, in practice the
fastest way to send a packet out, is to directly send the packet without
using a dedicated traffic class thread. This is why by default the
CONFIG_NET_TC_TX_COUNT option is set to 0 if userspace is
not enabled. If userspace is enabled, then the minimum TX traffic class
count is 1. Reason for this is that the userspace application does not
have enough permissions to deliver the message directly.
In receiving side, it is recommended to have at least one receiving traffic
class queue. Reason is that typically the network device driver is running
in IRQ context when it receives the packet, in which case it should not try
to deliver the network packet directly to the upper layers, but to place
the packet to the traffic class queue. If the network device driver is not
running in IRQ context when it gets the packet, then the RX traffic class
option CONFIG_NET_TC_RX_COUNT could be set to 0.
Stack Size Options
There several network specific threads in a network enabled system. Some of the threads might depend on a configure option which can be used to enable or disable a feature. Each thread stack size is optimized to allow normal network operations.
The network management API is using a dedicated thread by default. The thread
is responsible to deliver network management events to the event listeners that
are setup in the system if the CONFIG_NET_MGMT and
CONFIG_NET_MGMT_EVENT options are enabled.
If the options are enabled, the user is able to register a callback function
that the net_mgmt thread is calling for each network management event.
By default the net_mgmt event thread stack size is rather small.
The idea is that the callback function does minimal things so that new
events can be delivered to listeners as fast as possible and they are not lost.
The net_mgmt event thread stack size is controlled by
CONFIG_NET_MGMT_EVENT_QUEUE_SIZE option. It is recommended
to not do any blocking operations in the callback function.
The network thread stack utilization can be monitored from kernel shell by the kernel threads command.