infineon,xmc4xxx-spi
Vendor: Infineon Technologies
Description
These nodes are “spi” bus nodes.
INFINEON XMC4XXX SPI controller
Properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
Clock frequency the SPI peripheral is being driven at, in Hz.
|
|
|
An array of chip select GPIOs to use. Each element
in the array specifies a GPIO. The index in the array
corresponds to the child node that the CS gpio controls.
Example:
spi@... {
cs-gpios = <&gpio0 23 GPIO_ACTIVE_LOW>,
<&gpio1 10 GPIO_ACTIVE_LOW>,
...;
spi-device@0 {
reg = <0>;
...
};
spi-device@1 {
reg = <1>;
...
};
...
};
The child node "spi-device@0" specifies a SPI device with
chip select controller gpio0, pin 23, and devicetree
GPIO flags GPIO_ACTIVE_LOW. Similarly, "spi-device@1" has CS GPIO
controller gpio1, pin 10, and flags GPIO_ACTIVE_LOW. Additional
devices can be configured in the same way.
If unsure about the flags cell, GPIO_ACTIVE_LOW is generally a safe
choice for a typical "CSn" pin. GPIO_ACTIVE_HIGH may be used if
intervening hardware inverts the signal to the peripheral device or
the line itself is active high.
If this property is not defined, no chip select GPIOs are set.
SPI controllers with dedicated CS pins do not need to define
the cs-gpios property.
|
|
|
Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.
This property is required. |
|
|
Pin configuration/s for the second state. See pinctrl-0.
|
|
|
Pin configuration/s for the third state. See pinctrl-0.
|
|
|
Pin configuration/s for the fourth state. See pinctrl-0.
|
|
|
Pin configuration/s for the fifth state. See pinctrl-0.
|
|
|
Names for the provided states. The number of names needs to match the
number of states.
This property is required. |
|
|
Connects the SPI miso line (USIC DX0 input) to a specific GPIO pin.
The USIC DX0 input is a multiplexer which connects to different GPIO pins.
Refer to the XMC4XXX reference manual for the GPIO pin/mux mappings. DX0G
is the loopback input line.
This property is required. Legal values: |
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “infineon,xmc4xxx-spi” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Power domain the device belongs to.
The device will be notified when the power domain it belongs to is either
suspended or resumed.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
register space
This property is required. See Important properties for more information. |
|
|
name of each register space
|
|
|
IRQ number and priority to use for interrupt driven SPI. If DMA is not used (enabled using
option CONFIG_SPI_XMC4XXX_DMA) then only one, for receiving, labelled with "rx" needs to be
set. When using DMA, two interrupts labelled "tx" and "rx" must be set.
Each USIC must use a certain interrupt range:
USIC0 = [84, 89]
USIC1 = [90, 95]
USIC2 = [96, 101]
See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
Human readable string describing the device (used as device_get_binding() argument)
See Important properties for more information. This property is deprecated. |
|
|
Clock gate information
|
|
|
name of each clock
|
|
|
number of address cells in reg property
This property is required. Constant value: |
|
|
number of size cells in reg property
This property is required. |
|
|
Optional TX & RX dma specifiers.
The dmas are referenced in the USIC/SPI node using the following syntax:
dmas = <&dma1 1 0 XMC4XXX_SET_CONFIG(10,6)>, <&dma1 2 0 XMC4XXX_SET_CONFIG(11,6)>;
where the first entry is for the TX, and the second for RX.
The parameters in the dma entry are: dma device phandle, dma channel, dma priority (0 is
lowest and 7 is highest), and an opaque entry for the dma line routing parameters set
by the macro XMC4XXX_SET_CONFIG(line, request_source). Use the following steps to properly
select parameters line, request_source:
1. Select a dma device and a free dma channel.
1. Select a free dma line. dma0 device can only connect to lines [0, 7] and
dma1 can connect to lines [8, 11].
2. For a given interrupt, calculate the service request (SR) number. Note the following
simple mapping: in USIC0 interrupt 84->SR0, interrupt 85->SR1, ... etc.
In USIC1, interrupt 90->SR0, 91->SR1, etc.
3. Select request_source from Table "DMA Request Source Selection" in XMC4XXX reference
manual.
For example, say we select interrupt 85 on USIC0, dma0, channel 3, priority 4, and line 7.
The interrupt would map to SR1. From Table "DMA Request Source Selection", request_source
would need to be set to 10 and the dts entry would be:
dma = <&dma0 3 4 XMC4XXX_SET_CONFIG(7,10) ... >;
|
|
|
Required if the dmas property exists. Should be set to "tx" and "rx"
to match the dmas property.
For example
dma-names = "tx", "rx";
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|