arduino-header-r3
Vendor: Generic or vendor-independent
Description
GPIO pins exposed on Arduino Uno (R3) headers.
The Arduino Uno layout provides four headers, two each along
opposite edges of the board.
Proceeding counter-clockwise:
* An 8-pin Power Supply header. No pins on this header are exposed
by this binding.
* A 6-pin Analog Input header. This has analog input signals
labeled from A0 at the top through A5 at the bottom.
* An 8-pin header (opposite Analog Input). This has digital input
signals labeled from D0 at the bottom D7 at the top;
* A 10-pin header (opposite Power Supply). This has six additional
digital input signals labelled from D8 at the bottom through D13
towards the top, skipping two pins, then finishing with D14 and
D15 at the top.
This binding provides a nexus mapping for 20 pins where parent pins 0
through 5 correspond to A0 through A5, and parent pins 6 through 21
correspond to D0 through D15, as depicted below:
D15 21
D14 20
AREF -
GND -
- N/C D13 19
- IOREF D12 18
- RESET D11 17
- 3V3 D10 16
- 5V D9 15
- GND D8 14
- GND
- VIN D7 13
D6 12
0 A0 D5 11
1 A1 D4 10
2 A2 D3 9
3 A3 D2 8
4 A4 D1 7
5 A5 D0 6
Properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
This property is required. |
|
|
|
|
|
|
|
|
Number of items to expect in a GPIO specifier
This property is required. |
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “arduino-header-r3” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Power domain the device belongs to.
The device will be notified when the power domain it belongs to is either
suspended or resumed.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
register space
See Important properties for more information. |
|
|
name of each register space
|
|
|
interrupts for device
See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
Human readable string describing the device (used as device_get_binding() argument)
See Important properties for more information. This property is deprecated. |
|
|
Clock gate information
|
|
|
name of each clock
|
|
|
number of address cells in reg property
|
|
|
number of size cells in reg property
|
|
|
DMA channels specifiers
|
|
|
Provided names of DMA channel specifiers
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|