kvaser,pcican
Vendor: Kvaser
Description
Kvaser PCIcan
Properties
Top level properties
These property descriptions apply to “kvaser,pcican” nodes themselves. This page also describes child node properties in the following sections.
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
Initial bitrate in bit/s. If this is unset, the initial bitrate is set to
CONFIG_CAN_DEFAULT_BITRATE.
|
|
|
Initial sample point in per mille (e.g. 875 equals 87.5%).
If this is unset (or if it is set to 0), the initial sample point will default to 75.0% for
bitrates over 800 kbit/s, 80.0% for bitrates over 500 kbit/s, and 87.5% for all other
bitrates.
|
|
|
Actively controlled CAN transceiver.
Example:
transceiver0: can-phy0 {
compatible = "nxp,tja1040", "can-transceiver-gpio";
standby-gpios = <gpioa 0 GPIO_ACTIVE_HIGH>;
max-bitrate = <1000000>;
#phy-cells = <0>;
};
&can0 {
status = "okay";
phys = <&transceiver0>;
};
|
|
|
Vendor ID of the device
|
|
|
Device ID of the device
|
|
|
Optional class/revision register filter
|
|
|
Class/revision register mask
|
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “kvaser,pcican” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Power domain the device belongs to.
The device will be notified when the power domain it belongs to is either
suspended or resumed.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
register space
See Important properties for more information. |
|
|
name of each register space
|
|
|
interrupts for device
This property is required. See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
Human readable string describing the device (used as device_get_binding() argument)
See Important properties for more information. This property is deprecated. |
|
|
Clock gate information
|
|
|
name of each clock
|
|
|
number of address cells in reg property
|
|
|
number of size cells in reg property
|
|
|
DMA channels specifiers
|
|
|
Provided names of DMA channel specifiers
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|
Child node properties
Name |
Type |
Details |
|---|---|---|
|
|
The minimum bitrate supported by the CAN transceiver in bits/s.
|
|
|
The maximum bitrate supported by the CAN transceiver in bits/s.
This property is required. |