Waveshare Pico UPS-B shield

Overview

The Waveshare Pico UPS-B shield is an uninterruptible Power supply (UPS) module designed for the Raspberry Pi Pico which uses the Texas Instruments’ INA219 current/power Monitor. It communicates with the Raspberry Pi Pico over I2C

Waveshare Pico UPS-B shield

Hardware

• INA219

  • Senses bus voltages from 0 to 26 V

  • Reports current, voltage and power

  • 16 Programmable Addresses

  • SOT23-8 and SOIC-8 packages

  • Calibration registers

• ETA6003

  • Switching charger with power path management

  • Up to 95% DC-DC efficiency

  • 0mΩ power path MOSFET

  • Up to 2.5A max charging current

• Connectivity

  • Raspberry Pi Pico compatible (I2C)

  • 2 pin jst header for Li-po battery

——-+———————–+—————————+ | Name | Function | Usage | +=======+=======================+===========================+ | GP0 | None | | +——-+———————–+—————————+ | GP1 | None | | +——-+———————–+—————————+ | GP2 | None | | +——-+———————–+—————————+ | GP3 | None | | +——-+———————–+—————————+ | GP4 | None | | +——-+———————–+—————————+ | GP5 | None | | +——-+———————–+—————————+ | GP6 | I2C1_SDA ACTIVE_LOW | INA219 | +——-+———————–+—————————+ | GP7 | I2C1_SCL ACTIVE_LOW | INA219 | +——-+———————–+—————————+ | GP8 | None | | +——-+———————–+—————————+ | GP9 | None | | +——-+———————–+—————————+ | GP10 | None | | +——-+———————–+—————————+ | GP11 | None | | +——-+———————–+—————————+ | GP12 | None | | +——-+———————–+—————————+ | GP13 | None | | +——-+———————–+—————————+ | GP14 | None | | +——-+———————–+—————————+ | GP15 | None | | +——-+———————–+—————————+ | GP16 | None | | +——-+———————–+—————————+ | GP17 | None | | +——-+———————–+—————————+ | GP18 | None | | +——-+———————–+—————————+ | GP19 | None | | +——-+———————–+—————————+ | GP20 | None | | +——-+———————–+—————————+ | GP21 | None | | +——-+———————–+—————————+ | GP22 | None | | +——-+———————–+—————————+ | GP23 | None | | +——-+———————–+—————————+ | GP24 | None | | +——-+———————–+—————————+ | GP25 | None | | +——-+———————–+—————————+ | GP26 | None | | +——-+———————–+—————————+ | GP27 | None | | +——-+———————–+—————————+ | GP28 | None | | +——-+———————–+—————————+

• Power Supply

  • 3.3V ~ 5V

• Components

  • Power switch

  • Power LED

  • Charging LED

For more information about the Waveshare Pico UPS-B:

• Waveshare Pico UPS website

• INA219 data sheet

• ETA6003 data sheet

Programming

Set -DSHIELD=waveshare_pico_ups_b when you invoke west build or cmake in your Zephyr application. For example:

Using west:

# From the root of the zephyr repository
west build -b rpi_pico samples/sensor/ina219 -- -DSHIELD=waveshare_pico_ups_b
west flash

Using CMake and ninja:

# From the root of the zephyr repository
# Use cmake to configure a Ninja-based buildsystem:
cmake -Bbuild -GNinja -DBOARD=rpi_pico -DSHIELD=waveshare_pico_ups_b samples/sensor/ina219

# Now run the build tool on the generated build system:
ninja -Cbuild
ninja -Cbuild flash