Laird Connectivity BL654 USB (451-00004)

Overview

The BL654 USB adapter hardware (Laird Connectivity part 451-00004) provides support for the Laird Connectivity BL654 module powered by a Nordic Semiconductor nRF52840 ARM Cortex-M4F CPU.

This USB adapter has the following features:

  • CLOCK

  • FLASH

  • GPIO

  • MPU

  • NVIC

  • PWM

  • RADIO (Bluetooth Low Energy and 802.15.4)

  • USB

  • WDT

  • RTC

BL654 USB adapter

BL654 USB Adapter

451-00004 Box Contents

BL654 USB Adapter PCB

More information about the BL654 USB adapter can be found on the BL654 USB Dongle Quick Start Guide [1]. There is more information on the BL654 range on the BL654 website [2].

Hardware

Supported Features

The BL654 USB board configuration supports the following hardware features:

Interface

Controller

Driver/Component

CLOCK

on-chip

clock_control

FLASH

on-chip

flash

GPIO

on-chip

gpio

MPU

on-chip

arch/arm

NVIC

on-chip

arch/arm

PWM

on-chip

pwm

RADIO

on-chip

Bluetooth, ieee802154

RTC

on-chip

system clock

USB

on-chip

usb

WDT

on-chip

watchdog

Other hardware features have not been enabled yet for this board. See BL654 website [2] for a complete list of BL654 USB adapter hardware features.

Connections and IOs

LED

  • LED1 (blue) = P0.13

Push buttons

  • RESET = SW1 = nReset

Serial Port

Zephyr console output is available as follows:

  • using the USB connector, which may be used to make the console available on PC as USB CDC class.

Programming and Debugging

Applications for the bl654_usb board configuration can be built in the usual way (see Building an Application for more details). The bl654_usb board cannot be used for debugging. The compatible BL654 DVK board can be used for development. Documentation can be found at the Laird Connectivity BL654 DVK site and boards/lairdconnect/bl654_dvk/doc/bl654_dvk.rst

Flashing

The board supports programming using the built-in bootloader.

The board is factory-programmed with a Laird Connectivity variation of Nordic’s open bootloader from Nordic’s nRF5x SDK. With this option, you’ll use Nordic’s nrfutil [3] program to create firmware packages supported by this bootloader and flash them to the device. Make sure nrfutil is installed before proceeding. These instructions were tested with version 6.1.0.

  1. With the adapter plugged in, reset the board into the bootloader by pressing the RESET button.

    The push button is in a pin-hole on the logo side of the USB adapter.

    Location of RESET button

    The blue LED should start a fade pattern, signalling the bootloader is running.

  2. Compile a Zephyr application; we’ll use Blinky.

    west build -b bl654_usb zephyr/samples/basic/blinky

  3. Package the application for the bootloader using nrfutil:

    nrfutil pkg generate --hw-version 52 --sd-req=0x00 \
        --application build/zephyr/zephyr.hex \
        --application-version 1 blinky.zip

  4. Flash it onto the board. Note /dev/ttyACM0 is for Linux; it will be something like COMx on Windows, and something else on macOS.

    nrfutil dfu usb-serial -pkg blinky.zip -p /dev/ttyACM0

    When this command exits, observe the blue LED on the board blinking.

Testing Bluetooth on the BL654 USB

Many of the Bluetooth examples will work on the BL654 USB. Try them out:

Testing the LED on the BL654 USB

There is a sample that allows you to test that the LED on the board is working properly with Zephyr:

You can build and flash the example to make sure Zephyr is running correctly on your board. The LED definitions can be found in boards/lairdconnect/bl654_usb/bl654_usb.dts.

References