Getting started with nRF52 Series

This guide lets you evaluate the nRF Connect SDK’s support for nRF52 Series Development Kit (DK) without the need of installing the SDK. It tells you how to install the Bluetooth: Peripheral UART sample and perform a quick test of your DK.

If you want to go through an online training course to familiarize yourself with Bluetooth Low Energy and the development of Bluetooth LE applications, enroll in the Bluetooth LE Fundamentals course in the Nordic Developer Academy.

Minimum requirements

Make sure you have all the required hardware and that your computer and mobile device both have one of the supported operating systems.

Hardware

  • One of the following nRF52 Series development kits:

    • nRF52840 DK

    • nRF52833 DK

    • nRF52 DK

  • Micro-USB 2.0 cable

Software

On your computer, one of the following operating systems:

  • Microsoft Windows

  • macOS

  • Ubuntu Linux

The operating system versions that support the nRF Connect SDK tools are listed in the Supported operating systems section.

On your mobile device, one of the following operating systems:

  • Android

  • iOS

Installing the required software

On your computer, install nRF Connect for Desktop. After installing and starting the application, install the Programmer app.

You must also install a terminal emulator, such as nRF Connect Serial Terminal, the nRF Terminal (part of the nRF Connect for Visual Studio Code extension), or PuTTY. nRF Connect Serial Terminal is the recommended method for Connecting to the sample.

On your mobile device, install the nRF Connect for Mobile application from the corresponding application store.

Installing the sample

You must program and run a precompiled version of the Bluetooth: Peripheral UART sample on your development kit to test the functions.

Download the precompiled version of the sample for your DK from the corresponding download page:

After downloading the zip archive, extract it to a folder of your choice. The archive contains the HEX file used to program the sample to your DK.

To program the precompiled sample to your development kit, complete the following steps:

  1. Open the Programmer app.

  2. Connect the nRF52 Series DK to the computer with a micro-USB cable and turn on the DK.

    LED1 starts blinking.

  3. Click SELECT DEVICE and select the DK from the drop-down list.

    Programmer - Select Device

    Programmer - Select Device

    The drop-down text changes to the type of the selected device, with its SEGGER ID below the name. The Device Memory Layout section also changes its name to the device name, and indicates that the device is connected. If the Auto read memory option is selected in the DEVICE section of the side panel, the memory layout will update. If it is not selected and you wish to see the memory layout, click Read in the DEVICE section of the side panel.

  4. Click Add file in the FILE section, and select Browse.

  5. Navigate to where you extracted the HEX file and select it.

  6. Click the Erase & write button in the DEVICE section to program the DK.

    Do not unplug or turn off the DK during this process.

Note

If you experience any problems during the process, press Ctrl+R (command+R on macOS) to restart the Programmer app, and try again.

After you have programmed the sample to the DK, you can connect to it using a terminal emulator and test the functions.

Connecting to the sample

You can connect to the sample on the nRF52 Series DK with a terminal emulator on your computer using Universal Asynchronous Receiver/Transmitter (UART). This allows you to see the logging information the sample outputs as well as to enter console inputs.

You can use an external UART to USB bridge. UART communication through the UART to USB CDC ACM bridge is referred to as CDC-UART. This is different from communication through the Nordic UART Service (NUS) over Bluetooth® Low Energy (LE).

If you have problems connecting to the sample, restart the DK and start over.

To connect using CDC-UART, complete the steps listed on the Testing and optimization page for the chosen terminal emulator.

Once the connection has been established, continue to Testing the sample.

Testing the sample

You can test the Bluetooth: Peripheral UART sample on your DK using the nRF Connect for Mobile application. The test requires that you have connected to the sample and have the connected terminal emulator open.

To perform tests, complete the following steps:

  1. Make sure the nRF52 Series DK is connected to the computer with a micro-USB cable and has been turned on (LED1 is blinking).

  2. Open the nRF Connect for Mobile application on your Android device.

  3. In nRF Connect for Mobile, tap Scan.

  4. Find the DK in the list, select it and tap Connect.

    The default device name for the Peripheral UART sample is Nordic_UART_Service.

  5. When connected, tap the three-dot menu below the device name, and select Enable CCCDs.

    This example communicates over Bluetooth Low Energy using the Nordic UART Service (NUS).

    nRF Connect for Mobile - Enable services option

    nRF Connect for Mobile - Enable services option

  6. Tap the three-dot menu next to Disconnect and select Show log.

  7. On your computer, in the terminal emulator connected to the sample through CDC-UART, type hello and send it to the DK.

    The text is sent through the nRF52 Series DK to your mobile device over a Bluetooth LE link. The device displays the text in the nRF Connect for Mobile log:

    nRF Connect for Mobile - Text shown in the log

    nRF Connect for Mobile - Text shown in the log

If you have a dongle or a second Nordic Semiconductor DK, you can test the sample using a computer instead of using this process.

Next steps

You have now completed getting started with the nRF52 Series DK. See the following links for where to go next: