espressif,esp32-i2c

Description

These nodes are “i2c” bus nodes.

ESP32 I2C

Properties

Properties not inherited from the base binding file.

Name	Type	Details
`pinctrl-0`	`phandles`	Pin configuration/s for the first state. Content is specific to the selected pin controller driver implementation. This property is required.
`pinctrl-names`	`string-array`	Names for the provided states. The number of names needs to match the number of states. This property is required.
`scl-gpios`	`phandle-array`	GPIO to which the I2C SCL signal is routed. This is only required if the target SoC does not have support in hardware for clearing the I2C bus in case of a communication failure
`sda-gpios`	`phandle-array`	GPIO to which the I2C SDA signal is routed. This is only required if the target SoC does not have support in hardware for clearing the I2C bus in case of a communication failure
`tx-lsb`	`boolean`	Set I2C TX data as LSB
`rx-lsb`	`boolean`	Set I2C RX data as LSB
`scl-timeout-us`	`int`	Timeout for unchanged SCL during clock stretching of the I2C target in microseconds. If not set or 0, the timeout is disabled or set to the maximum possible value if the MCU does not support disabling the timeout.
`clock-frequency`	`int`	Initial clock frequency in Hz
`pinctrl-1`	`phandles`	Pin configuration/s for the second state. See pinctrl-0.
`pinctrl-2`	`phandles`	Pin configuration/s for the third state. See pinctrl-0.
`pinctrl-3`	`phandles`	Pin configuration/s for the fourth state. See pinctrl-0.
`pinctrl-4`	`phandles`	Pin configuration/s for the fifth state. See pinctrl-0.

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “espressif,esp32-i2c” compatible.

Name	Type	Details
`reg`	`array`	register space This property is required. See Important properties for more information.
`#address-cells`	`int`	number of address cells in reg property This property is required. Constant value: `1`
`#size-cells`	`int`	number of size cells in reg property This property is required.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`power-domain`	`phandle`	Power domain the device belongs to. The device will be notified when the power domain it belongs to is either suspended or resumed.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.