ilitek,ili9341 (on spi bus)

Vendor: ILI Technology Corporation (ILITEK)

Description

ILI9341 320x240 display controller

Properties

Properties not inherited from the base binding file.

Name

Type

Details

ifmode

uint8-array

 
RGB interface signal control (IFMOD) register value.

Default value: [64]

ifctl

uint8-array

 
Interface control (IFCTL) register value.

Default value: [1, 0, 0]

pwctrla

uint8-array

 
Power control A (PWCTRLA) register value.

Default value: [57, 44, 0, 52, 2]

pwctrlb

uint8-array

 
Power control B (PWCTRLB) register value.

Default value: [0, 139, 48]

pwseqctrl

uint8-array

 
Power on sequence control (PWSEQCTRL) register value.

Default value: [85, 1, 35, 1]

timctrla

uint8-array

 
Driver timing control A (TIMCTRLA) register value.

Default value: [132, 17, 122]

timctrlb

uint8-array

 
Driver timing control B (TIMCTRLB) register value.

Default value: [0, 0]

pumpratioctrl

uint8-array

 
Pump ratio control (PUMPRATIOCTRL) register value.

Default value: [16]

enable3g

uint8-array

 
Enable 3G (ENABLE3G) register value.

Default value: [2]

etmod

uint8-array

 
Entry Mode Set (ETMOD) register value.

Default value: [6]

gamset

uint8-array

 
Gamma set (GAMSET) register value.

Default value: [1]

frmctr1

uint8-array

 
Frame rate control (in normal mode / full colors) (FRMCTR1) register value.

Default value: [0, 27]

disctrl

uint8-array

 
Display function control (DISCTRL) register value. Note that changing default SS bit value (0) may interfere with display rotation.

Default value: [10, 130, 39, 4]

pwctrl1

uint8-array

 
Power control 1 (PWCTRL1) register values.

Default value: [33]

pwctrl2

uint8-array

 
Power control 2 (PWCTRL2) register values.

Default value: [16]

vmctrl1

uint8-array

 
VCOM control 1 (VMCTRL1) register values.

Default value: [49, 60]

vmctrl2

uint8-array

 
VCOM control 2 (VMCTRL2) register values.

Default value: [192]

pgamctrl

uint8-array

 
Positive gamma correction (PGAMCTRL) register values.

Default value: [15, 34, 31, 10, 14, 6, 77, 118, 59, 3, 14, 4, 19, 14, 12]

ngamctrl

uint8-array

 
Negative gamma correction (NGAMCTRL) register values.

Default value: [12, 35, 38, 4, 16, 4, 57, 36, 75, 3, 11, 11, 51, 55, 15]

reset-gpios

phandle-array

 
RESET pin.
The RESET pin of ILI9340 is active low. If connected directly the MCU pin should be configured as active low.

cmd-data-gpios

phandle-array

 
D/CX pin.
The D/CX pin of ILI9340 is active low (transmission command byte). If connected directly the MCU pin should be configured as active low.

This property is required.

pixel-format

int

 
Display pixel format. Note that when RGB888 pixel format is selected only 6 color bits are actually used being in practice equivalent to RGB666.

Legal values: 0, 1

rotation

int

 
Display rotation (CW) in degrees.

Legal values: 0, 90, 180, 270

display-inversion

boolean

 
Display inversion mode. Every bit is inverted from the frame memory to the display.

spi-max-frequency

int

 
Maximum clock frequency of device's SPI interface in Hz

This property is required.

duplex

int

 
Duplex mode, full or half. By default it's always full duplex thus 0
as this is, by far, the most common mode.
Use the macros not the actual enum value, here is the concordance
list (see dt-bindings/spi/spi.h)
  0    SPI_FULL_DUPLEX
  2048 SPI_HALF_DUPLEX

Legal values: 0, 2048

frame-format

int

 
Motorola or TI frame format. By default it's always Motorola's,
thus 0 as this is, by far, the most common format.
Use the macros not the actual enum value, here is the concordance
list (see dt-bindings/spi/spi.h)
  0     SPI_FRAME_FORMAT_MOTOROLA
  32768 SPI_FRAME_FORMAT_TI

Legal values: 0, 32768

supply-gpios

phandle-array

 
GPIO specifier that controls power to the device.

This property should be provided when the device has a dedicated
switch that controls power to the device.  The supply state is
entirely the responsibility of the device driver.

Contrast with vin-supply.

vin-supply

phandle

 
Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.

This property should be provided when device power is supplied
by a shared regulator.  The supply state is dependent on the
request status of all devices fed by the regulator.

Contrast with supply-gpios.  If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.

height

int

 
Height of the panel driven by the controller, with the units in pixels.

This property is required.

width

int

 
Width of the panel driven by the controller, with the units in pixels.

This property is required.