Zigbee FOTA

The Zigbee firmware over-the-air (Zigbee FOTA) library provides Zigbee endpoint definition, which implements clusters responsible for transferring a firmware file through the Zigbee network. The received data is passed as an upgrade candidate through the DFU multi-image library API to the DFU target.

The library uses the endpoint to:

  • Discover Zigbee OTA server by sending Match Descriptor Request broadcast messages.

  • Query the discovered server periodically to check if there is a suitable image for the update.

  • Transfer the new firmware using the ZCL OTA cluster commands.

  • Allow the OTA server to manage the upgrade process using the ZCL OTA control commands.

When used, the Zigbee FOTA library replaces the FOTA download library in nRF Connect SDK.

Note

The Zigbee FOTA functionality is available for the Zigbee: Light switch sample.

OTA upgrade entities

The following entities participate in the Zigbee OTA Upgrade process:

  • OTA Upgrade Client – Runs on the target, that is the device that is being upgraded, and is responsible for downloading and installing the new firmware.

  • OTA Upgrade Server – Provides the firmware image. The OTA Upgrade Server can be either a standalone third-party device or it can be instantiated on an nRF52840 DK using nRF Util’s DFU over Zigbee procedure.

OTA upgrade process

The OTA Upgrade Client queries for OTA Upgrade Servers with the intervals defined by the CONFIG_ZIGBEE_FOTA_SERVER_DISOVERY_INTERVAL_HRS Kconfig option until at least one server is found. Once found, the client starts to query the server for images. The interval between queries for the available Zigbee FOTA images is defined by the CONFIG_ZIGBEE_FOTA_IMAGE_QUERY_INTERVAL_MIN Kconfig option. After querying the OTA Upgrade Server for available images and receiving information about the image, the library begins the OTA upgrade process. The library uses ZBOSS Zigbee stack’s ZCL API to download the image.

After the OTA Upgrade Client downloads the Zigbee OTA image header, the stack verifies the following mandatory fields:

If all values are accepted, the OTA Upgrade Client downloads the first fragment of the firmware image.

Once the download is started, all received data fragments are passed to the DFU multi-image library. The library takes care of where the upgrade candidate is stored, depending on the image type that is being downloaded.

When the download is completed, the download client sends an appropriate event. At this point, the received firmware is tagged as an upgrade candidate and the OTA server is queried for an update time.

Once the OTA server triggers the update process, the library sends a ZIGBEE_FOTA_EVT_FINISHED callback event. When the consumer of the library receives this event, it should issue a reboot command to apply the upgrade.

Configuration

To enable the Zigbee FOTA library, set the CONFIG_ZIGBEE_FOTA Kconfig option.

To configure the Zigbee FOTA library, use the following options:

For detailed steps about configuring the library in a Zigbee sample or application, see Configuring Zigbee FOTA.

Limitations

The Zigbee FOTA library has the following limitations:

  • The endpoint definition in the library includes the endpoint ID, defined with CONFIG_ZIGBEE_FOTA_ENDPOINT. When using the Zigbee FOTA library, this endpoint ID cannot be used for other endpoints.

  • The Zigbee FOTA upgrades are currently only supported on the nRF52840 DK (PCA10056) and nRF5340 DK (PCA10095).

  • The Zigbee FOTA library does not currently support bootloader upgrades.

Additionally, the following limitations apply on the nRF5340 SoCs:

  • It is required to use external flash to enable the Zigbee FOTA library.

  • By default, only the full upgrades (to both application and network core) are allowed. Disable the CONFIG_NRF53_ENFORCE_IMAGE_VERSION_EQUALITY Kconfig option to build update images without inter-dependencies so that they can be applied independently.

  • It is impossible to enable CONFIG_BOOT_SWAP_USING_MOVE Kconfig option. As a result, the fallback recovery is not available and any valid upgrade will overwrite the previous image. The call to the boot_write_img_confirmed() will have no effect.

  • The current DFU limitations and dependencies are enforced by the CONFIG_NRF53_MULTI_IMAGE_UPDATE Kconfig option.

  • The version of the network core image is always set to the same value as the application core image. Its value can be configured using the CONFIG_MCUBOOT_IMGTOOL_SIGN_VERSION Kconfig option.

  • The MCUboot header is not stored inside the network core flash memory. As a result, it is impossible to read the version of the currently running network core image.

API documentation

Header file: include/zigbee/zigbee_fota.h
Source files: subsys/zigbee/lib/zigbee_fota/src/
group zigbee_fota

Library for downloading a firmware update through Zigbee network.

Discovers Zigbee OTA server, queries it for new images and downloads the matching file to the secondary partition of MCUboot. After the file has been downloaded, the secondary slot is tagged as having valid firmware inside it.

Defines

ZIGBEE_FOTA_EVT_DL_COMPLETE_VAL

Typedefs

typedef void (*zigbee_fota_callback_t)(const struct zigbee_fota_evt *evt)

Zigbee FOTA download asynchronous callback function.

Param evt:

Event.

Enums

enum zigbee_fota_evt_id

Zigbee FOTA download event IDs.

Values:

enumerator ZIGBEE_FOTA_EVT_PROGRESS

Zigbee FOTA download progress report.

enumerator ZIGBEE_FOTA_EVT_FINISHED

Zigbee FOTA download finished.

enumerator ZIGBEE_FOTA_EVT_ERROR

Zigbee FOTA download error.

Functions

int zigbee_fota_init(zigbee_fota_callback_t client_callback)

Initialize the Zigbee firmware over-the-air download library.

Parameters:

  • client_callback – Callback for the generated events.

Return values:

0 – If successfully initialized. Otherwise, a negative value is returned.

void zigbee_fota_abort(void)

Abort all pending updates performed via Zigbee network.

void zigbee_fota_signal_handler(zb_bufid_t bufid)

Function for passing Zigbee stack signals to the Zigbee FOTA logic.

Parameters:

  • bufid – [in] Reference to the Zigbee stack buffer used to pass signal.

void zigbee_fota_zcl_cb(zb_bufid_t bufid)

Function for passing ZCL callback events to the Zigbee FOTA logic.

Parameters:

  • bufid – [in] Reference to the Zigbee stack buffer used to pass event.

struct zigbee_fota_event_dl
#include <zigbee_fota.h>

Zigbee FOTA download progress event data.

struct zigbee_fota_evt
#include <zigbee_fota.h>

Zigbee FOTA download event data.