nxp,mipi-dsi-2l

Description

These nodes are “mipi-dsi” bus nodes.

NXP MCUX MIPI DSI 2L

Properties

Properties not inherited from the base binding file.

Name	Type	Details
`nxp,lcdif`	`phandle`	Instance of the LCDIF peripheral. This property is required.
`dpi-color-coding`	`string`	MIPI DPI interface color coding. Sets the distribution of RGB bits within the 24-bit d bus, as specified by the DPI specification. Legal values: `'16-bit-config-1'`, `'16-bit-config-2'`, `'16-bit-config-3'`, `'18-bit-config-1'`, `'18-bit-config-2'`, `'24-bit'`
`dpi-pixel-packet`	`string`	MIPI DSI pixel packet type send through DPI interface. Legal values: `'16-bit'`, `'18-bit'`, `'18-bit-loose'`, `'24-bit'`
`dpi-video-mode`	`string`	DPI video mode. Legal values: `'non-burst-sync-pulse'`, `'non-burst-sync-event'`, `'burst'`
`dpi-bllp-mode`	`string`	Behavior in BLLP (Blanking or Low-Power Interval). Legal values: `'low-power'`, `'blank'`, `'null'`
`autoinsert-eotp`	`boolean`	Automatically insert an EoTp short packet when switching from HS to LP mode.
`dphy-clk-div`	`int`	MIPI D-PHY clock divider. Must be set to ensure clock frequency is at least (pixel clock * bits per output pixel) / number of mipi data lanes This property is required.
`dphy-ref-frequency`	`int`	Maximum clock speed supported by the device, in Hz. Leave at default if no DPHY PLL is present

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nxp,mipi-dsi-2l” compatible.

Name	Type	Details
`interrupts`	`array`	interrupts for device This property is required. See Important properties for more information.
`#address-cells`	`int`	number of address cells in reg property This property is required. Constant value: `1`
`#size-cells`	`int`	number of size cells in reg property This property is required.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg`	`array`	register space See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`power-domain`	`phandle`	Power domain the device belongs to. The device will be notified when the power domain it belongs to is either suspended or resumed.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.