Pin Control

This is a high-level guide to pin control. See Pin Control API for API reference material.

Introduction

The hardware blocks that control pin multiplexing and pin configuration parameters such as pin direction, pull-up/down resistors, etc. are named pin controllers. The pin controller’s main users are SoC hardware peripherals, since the controller enables exposing peripheral signals, like for example, map I2C0 SDA signal to pin PX0. Not only that, but it usually allows configuring certain pin settings that are necessary for the correct functioning of a peripheral, for example, the slew-rate depending on the operating frequency. The available configuration options are vendor/SoC dependent and can range from simple pull-up/down options to more advanced settings such as debouncing, low-power modes, etc.

The way pin control is implemented in hardware is vendor/SoC specific. It is common to find a centralized approach, that is, all pin configuration parameters are controlled by a single hardware block (typically named pinmux), including signal mapping. Fig. 41 illustrates this approach. PX0 can be mapped to UART0_TX, I2C0_SCK or SPI0_MOSI depending on the AF control bits. Other configuration parameters such as pull-up/down are controlled in the same block via CONFIG bits. This model is used by several SoC families, such as many from NXP and STM32.

../../_images/hw-cent-control.svg — Fig. 41 Example of pin control centralized into a single per-pin block

Other vendors/SoCs use a distributed approach. In such case, the pin mapping and configuration are controlled by multiple hardware blocks. Fig. 42 illustrates a distributed approach where pin mapping is controlled by peripherals, such as in Nordic nRF SoCs.

../../_images/hw-dist-control.svg — Fig. 42 Example pin control distributed between peripheral registers and per-pin block

From a user perspective, there is no difference in pin controller usage regardless of the hardware implementation: a user will always apply a state. The only difference lies in the driver implementation. In general, implementing a pin controller driver for a hardware that uses a distributed approach requires more effort, since the driver needs to gather knowledge of peripheral dependent registers.

Pin control vs. GPIO

Some functionality covered by a pin controller driver overlaps with GPIO drivers. For example, pull-up/down resistors can usually be enabled by both the pin control driver and the GPIO driver. In Zephyr context, the pin control driver purpose is to perform peripheral signal multiplexing and configuration of other pin parameters required for the correct operation of that peripheral. Therefore, the main users of the pin control driver are SoC peripherals. In contrast, GPIO drivers are for general purpose control of a pin, that is, when its logic level is read or controlled manually.

State model

For a device driver to operate correctly, a certain pin configuration needs to be applied. Some device drivers require a static configuration, usually set up at initialization time. Others need to change the configuration at runtime depending on the operating conditions, for example, to enable a low-power mode when suspending the device. Such requirements are modeled using states, a concept that has been adapted from the one in the Linux kernel. Each device driver owns a set of states. Each state has a unique name and contains a full pin configuration set (see Table 38). This effectively means that states are independent of each other, so they do not need to be applied in any specific order. Another advantage of the state model is that it isolates device drivers from pin configuration.

Table 38 Example pin configuration encoded using the states model
`UART0` peripheral
`default` state		`sleep` state
TX	Pin: PA0 Pull: NONE Low Power: NO	TX	Pin: PA0 Pull: NONE Low Power: YES
RX	Pin: PA1 Pull: UP Low Power: NO	RX	Pin: PA1 Pull: NONE Low Power: YES

Standard states

The name assigned to pin control states or the number of them is up to the device driver requirements. In many cases a single state applied at initialization time will be sufficient, but in some other cases more will be required. In order to make things consistent, a naming convention has been established for the most common use cases. Table 39 details the standardized states and its purpose.

Table 39 Standardized state names
State	Identifier	Purpose
`default`	`PINCTRL_STATE_DEFAULT`	State of the pins when the device is in operational state
`sleep`	`PINCTRL_STATE_SLEEP`	State of the pins when the device is in low power or sleep modes

Note that other standard states could be introduced in the future.

Custom states

Some device drivers may require using custom states beyond the standard ones. To achieve that, the device driver needs to have in its scope definitions for the custom state identifiers named as PINCTRL_STATE_{STATE_NAME}, where {STATE_NAME} is the capitalized state name. For example, if mystate has to be supported, a definition named PINCTRL_STATE_MYSTATE needs to be in the driver’s scope.

Note

It is important that custom state identifiers start from PINCTRL_STATE_PRIV_START

If custom states need to be accessed from outside the driver, for example to perform dynamic pin control, custom identifiers should be placed in a header that is publicly accessible.

Skipping states

In most situations, the states defined in Devicetree will be the ones used in the compiled firmware. However, there are some cases where certain states will be conditionally used depending on a compilation flag. A typical case is the sleep state. This state is only used in practice if CONFIG_PM_DEVICE is enabled. If a firmware variant without device power management is needed, one should in theory remove the sleep state from Devicetree to not waste ROM space storing such unused state.

States can be skipped by the pinctrl Devicetree macros if a definition named PINCTRL_SKIP_{STATE_NAME} expanding to 1 is present when pin control configuration is defined. In case of the sleep state, the pinctrl API already provides such definition conditional to the availability of device power management:

#ifndef CONFIG_PM_DEVICE
/** If device power management is not enabled, "sleep" state will be ignored. */
#define PINCTRL_SKIP_SLEEP 1
#endif

Dynamic pin control

Dynamic pin control refers to the capability of changing pin configuration at runtime. This feature can be useful in situations where the same firmware needs to run onto slightly different boards, each having a peripheral routed at a different set of pins. This feature can be enabled by setting CONFIG_PINCTRL_DYNAMIC.

Note

Dynamic pin control should only be used on devices that have not been initialized. Changing pin configurations while a device is operating may lead to unexpected behavior. Since Zephyr does not support device de-initialization yet, this functionality should only be used during early boot stages.

One of the effects of enabling dynamic pin control is that pinctrl_dev_config will be stored in RAM instead of ROM (not states or pin configurations, though). The user can then use pinctrl_update_states() to update the states stored in pinctrl_dev_config with a new set. This effectively means that the device driver will apply the pin configurations stored in the updated states when it applies a state.

Devicetree representation

Because Devicetree is meant to describe hardware, it is the natural choice when it comes to storing pin control configuration. In the following sections you will find an overview on how states and pin configurations are represented in Devicetree.

States

Given a device, each of its pin control state is represented in Devicetree by pinctrl-N properties, being N the state index starting from zero. The pinctrl-names property is then used to assign a unique identifier for each state property by index, for example, pinctrl-names list entry 0 is the name for pinctrl-0.

periph0: periph@0 {
    ...
    /* state 0 ("default") */
    pinctrl-0 = <...>;
    ...
    /* state N ("mystate") */
    pinctrl-N = <...>;
    /* names for state 0 up to state N */
    pinctrl-names = "default", ..., "mystate";
    ...
};

Pin configuration

There are multiple ways to represent the pin configurations in Devicetree. However, all end up encoding the same information: the pin multiplexing and the pin configuration parameters. For example, UART_RX is mapped to PX0 and pull-up is enabled. The representation choice largely depends on each vendor/SoC, so the Devicetree binding files for the pin control drivers are the best place to look for details.

A popular and versatile option is shown in the example below. One of the advantages of this choice is the grouping capability based on shared pin configuration. This allows to reduce the verbosity of the pin control definitions. Another advantage is that the pin configuration parameters for a particular state are enclosed in a single Devicetree node.

/* board.dts */
#include "board-pinctrl.dtsi"

&periph0 {
    pinctrl-0 = <&periph0_default>;
    pinctrl-names = "default";
};

/* vnd-soc-pkgxx.h
 * File with valid mappings for a specific package (may be autogenerated).
 * This file is optional, but recommended.
 */
...
#define PERIPH0_SIGA_PX0 VNDSOC_PIN(X, 0, MUX0)
#define PERIPH0_SIGB_PY7 VNDSOC_PIN(Y, 7, MUX4)
#define PERIPH0_SIGC_PZ1 VNDSOC_PIN(Z, 1, MUX2)
...

/* board-pinctrl.dtsi */
#include <vnd-soc-pkgxx.h>

&pinctrl {
    /* Node with pin configuration for default state */
    periph0_default: periph0_default {
        group1 {
            /* Mappings: PERIPH0_SIGA -> PX0, PERIPH0_SIGC -> PZ1 */
            pinmux = <PERIPH0_SIGA_PX0>, <PERIPH0_SIGC_PZ1>;
            /* Pins PX0 and PZ1 have pull-up enabled */
            bias-pull-up;
        };
        ...
        groupN {
            /* Mappings: PERIPH0_SIGB -> PY7 */
            pinmux = <PERIPH0_SIGB_PY7>;
        };
    };
};

Another popular model is based on having a node for each pin configuration and state. While this model may lead to shorter board pin control files, it also requires to have one node for each pin mapping and state, since in general, nodes can not be re-used for multiple states. This method is discouraged if autogeneration is not an option.

Note

Because all Devicetree information is parsed into a C header, it is important to make sure its size is kept to a minimum. For this reason it is important to prefix pre-generated nodes with /omit-if-no-ref/. This prefix makes sure that the node is discarded when not used.

/* board.dts */
#include "board-pinctrl.dtsi"

&periph0 {
    pinctrl-0 = <&periph0_siga_px0_default &periph0_sigb_py7_default
                 &periph0_sigc_pz1_default>;
    pinctrl-names = "default";
};

/* vnd-soc-pkgxx.dtsi
 * File with valid nodes for a specific package (may be autogenerated).
 * This file is optional, but recommended.
 */

&pinctrl {
    /* Mapping for PERIPH0_SIGA -> PX0, to be used for default state */
    /omit-if-no-ref/ periph0_siga_px0_default: periph0_siga_px0_default {
        pinmux = <VNDSOC_PIN(X, 0, MUX0)>;
    };

    /* Mapping for PERIPH0_SIGB -> PY7, to be used for default state */
    /omit-if-no-ref/ periph0_sigb_py7_default: periph0_sigb_py7_default {
        pinmux = <VNDSOC_PIN(Y, 7, MUX4)>;
    };

    /* Mapping for PERIPH0_SIGC -> PZ1, to be used for default state */
    /omit-if-no-ref/ periph0_sigc_pz1_default: periph0_sigc_pz1_default {
        pinmux = <VNDSOC_PIN(Z, 1, MUX2)>;
    };
};

/* board-pinctrl.dts */
#include <vnd-soc-pkgxx.dtsi>

/* Enable pull-up for PX0 (default state) */
&periph0_siga_px0_default {
    bias-pull-up;
};

/* Enable pull-up for PZ1 (default state) */
&periph0_sigc_pz1_default {
    bias-pull-up;
};

Note

It is discouraged to add pin configuration defaults in pre-defined nodes. In general, pin configurations depend on the board design or on the peripheral working conditions, so the decision should be made by the board. For example, enabling a pull-up by default may not always be desired because the board already has one or because its value depends on the operating bus speed. Another downside of defaults is that user may not be aware of them, for example:

/* not evident that "periph0_siga_px0_default" also implies "bias-pull-up" */
/omit-if-no-ref/ periph0_siga_px0_default: periph0_siga_px0_default {
    pinmux = <VNDSOC_PIN(X, 0, MUX0)>;
    bias-pull-up;
};

Implementation guidelines

Pin control drivers

Pin control drivers need to implement a single function: pinctrl_configure_pins(). This function receives an array of pin configurations that need to be applied. Furthermore, if CONFIG_PINCTRL_STORE_REG is set, it also receives the associated device register address for the given pins. This information may be required by some drivers to perform device specific actions.

The pin configuration is stored in an opaque type that is vendor/SoC dependent: pinctrl_soc_pin_t. This type needs to be defined in a header named pinctrl_soc.h file that is in the Zephyr’s include path. It can range from a simple integer value to a struct with multiple fields. pinctrl_soc.h also needs to define a macro named Z_PINCTRL_STATE_PINS_INIT that accepts two arguments: a node identifier and a property name (pinctrl-N). With this information the macro needs to define an initializer for all pin configurations contained within the pinctrl-N property of the given node.

Regarding Devicetree pin configuration representation, vendors can decide which option is better for their devices. However, the following guidelines should be followed:

Use pinctrl-N (N=0, 1, …) and pinctrl-names properties to define pin control states. These properties are defined in dts/bindings/pinctrl/pinctrl-device.yaml.
Use standard pin configuration properties as defined in dts/bindings/pinctrl/pincfg-node.yaml.

Representations not following these guidelines may be accepted if they are already used by the same vendor in other operating systems, e.g. Linux.

Device drivers

In this section you will find some tips on how a device driver should use the pinctrl API to successfully configure the pins it needs.

The device compatible needs to be modified in the corresponding binding so that the pinctrl-device.yaml is included. For example:

include: [base.yaml, pinctrl-device.yaml]

This file is needed to add pinctrl-N and pinctrl-names properties to the device.

From a device driver perspective there are two steps that need to be performed to be able to use the pinctrl API. First, the pin control configuration needs to be defined. This includes all states and pins. PINCTRL_DT_DEFINE or PINCTRL_DT_INST_DEFINE macros should be used for this purpose. Second, a reference to the device instance pinctrl_dev_config needs to be stored, since it is required to later use the API. This can be achieved using the PINCTRL_DT_DEV_CONFIG_GET and PINCTRL_DT_INST_DEV_CONFIG_GET macros.

It is worth to note that the only relationship between a device and its associated pin control configuration is based on variable naming conventions. The way an instance of pinctrl_dev_config is named for a corresponding device instance allows to later obtain a reference to it given the device’s Devicetree node identifier. This allows to minimize ROM usage, since only devices requiring pin control will own a reference to a pin control configuration.

Once the driver has defined the pin control configuration and kept a reference to it, it is ready to use the API. The most common way to apply a state is by using pinctrl_apply_state(). It is also possible to use the lower level function pinctrl_apply_state_direct() to skip state lookup if it is cached in advance (e.g. at init time). Since state lookup time is expected to be fast, it is recommended to use pinctrl_apply_state().

The example below contains a complete example of a device driver that uses the pinctrl API.

/* A driver for the "mydev" compatible device */
#define DT_DRV_COMPAT mydev

...
#include <zephyr/drivers/pinctrl.h>
...

struct mydev_config {
    ...
    /* Reference to mydev pinctrl configuration */
    const struct pinctrl_dev_config *pcfg;
    ...
};

...

static int mydev_init(const struct device *dev)
{
    const struct mydev_config *config = dev->config;
    int ret;
    ...
    /* Select "default" state at initialization time */
    ret = pinctrl_apply_state(config->pcfg, PINCTRL_STATE_DEFAULT);
    if (ret < 0) {
        return ret;
    }
    ...
}

#define MYDEV_DEFINE(i)                                                    \
    /* Define all pinctrl configuration for instance "i" */                \
    PINCTRL_DT_INST_DEFINE(i);                                             \
    ...                                                                    \
    static const struct mydev_config mydev_config_##i = {                  \
        ...                                                                \
        /* Keep a ref. to the pinctrl configuration for instance "i" */    \
        .pcfg = PINCTRL_DT_INST_DEV_CONFIG_GET(i),                         \
        ...                                                                \
    };                                                                     \
    ...                                                                    \
                                                                           \
    DEVICE_DT_INST_DEFINE(i, mydev_init, NULL, &mydev_data##i,             \
                          &mydev_config##i, ...);

DT_INST_FOREACH_STATUS_OKAY(MYDEV_DEFINE)

Pin Control API

group pinctrl_interface

Pin Controller Interface.

Pin control states

PINCTRL_STATE_DEFAULT: Default state (state used when the device is in operational state).

PINCTRL_STATE_SLEEP: Sleep state (state used when the device is in low power mode).

PINCTRL_STATE_PRIV_START: This and higher values refer to custom private states.

Defines

PINCTRL_REG_NONE: Utility macro to indicate no register is used.

PINCTRL_DT_DEV_CONFIG_DECLARE(node_id)

Declare pin control configuration for a given node identifier.

This macro should be used by tests or applications using runtime pin control to declare the pin control configuration for a device. PINCTRL_DT_DEV_CONFIG_GET can later be used to obtain a reference to such configuration.

Only available if CONFIG_PINCTRL_NON_STATIC is selected.

Parameters

node_id – Node identifier.

PINCTRL_DT_DEFINE(node_id)

Define all pin control information for the given node identifier.

This helper macro should be called together with device definition. It defines and initializes the pin control configuration for the device represented by node_id. Each pin control state (pinctrl-0, …, pinctrl-N) is also defined and initialized. Note that states marked to be skipped will not be defined (refer to Z_PINCTRL_SKIP_STATE for more details).

Parameters

node_id – Node identifier.

PINCTRL_DT_INST_DEFINE(inst)

Define all pin control information for the given compatible index.

See also

PINCTRL_DT_DEFINE

Parameters

inst – Instance number.

PINCTRL_DT_DEV_CONFIG_GET(node_id)

Obtain a reference to the pin control configuration given a node identifier.

Parameters

node_id – Node identifier.

PINCTRL_DT_INST_DEV_CONFIG_GET(inst)

Obtain a reference to the pin control configuration given current compatible instance number.

See also

PINCTRL_DT_DEV_CONFIG_GET

Parameters

inst – Instance number.

Functions

int pinctrl_lookup_state(const struct pinctrl_dev_config *config, uint8_t id, const struct pinctrl_state **state)

Find the state configuration for the given state id.

Parameters

config – Pin controller configuration.
id – Pin controller state id (see PINCTRL_STATES).
state – Found state.

Return values

0 – If state has been found.
-ENOENT – If the state has not been found.

int pinctrl_configure_pins(const pinctrl_soc_pin_t *pins, uint8_t pin_cnt, uintptr_t reg)

Configure a set of pins.

This function will configure the necessary hardware blocks to make the configuration immediately effective.

Warning

This function must never be used to configure pins used by an instantiated device driver.

Parameters

pins – List of pins to be configured.
pin_cnt – Number of pins.
reg – Device register (optional, use PINCTRL_REG_NONE if not used).

Return values

0 – If succeeded
-errno – Negative errno for other failures.

static inline int pinctrl_apply_state_direct(const struct pinctrl_dev_config *config, const struct pinctrl_state *state)

Apply a state directly from the provided state configuration.

Parameters

config – Pin control configuration.
state – State.

Return values

0 – If succeeded
-errno – Negative errno for other failures.

static inline int pinctrl_apply_state(const struct pinctrl_dev_config *config, uint8_t id)

Apply a state from the given device configuration.

Parameters

config – Pin control configuration.
id – Id of the state to be applied (see PINCTRL_STATES).

Return values

0 – If succeeded.
-ENOENT – If given state id does not exist.
-errno – Negative errno for other failures.

struct pinctrl_state

#include <pinctrl.h>

Pin control state configuration.

Public Members

const pinctrl_soc_pin_t *pins: Pin configurations.

uint8_t pin_cnt: Number of pin configurations.

uint8_t id: State identifier (see PINCTRL_STATES).

struct pinctrl_dev_config

#include <pinctrl.h>

Pin controller configuration for a given device.

Public Members

uintptr_t reg: Device address (only available if CONFIG_PINCTRL_STORE_REG is enabled).

const struct pinctrl_state *states: List of state configurations.

uint8_t state_cnt: Number of state configurations.

Dynamic pin control

group pinctrl_interface_dynamic

Defines

PINCTRL_DT_STATE_PINS_DEFINE(node_id, prop)

Helper macro to define the pins of a pin control state from Devicetree.

The name of the defined state pins variable is the same used by prop. This macro is expected to be used in conjunction with PINCTRL_DT_STATE_INIT.

See also

PINCTRL_DT_STATE_INIT

Parameters

node_id – Node identifier containing prop.
prop – Property within node_id containing state configuration.

PINCTRL_DT_STATE_INIT(prop, state)

Utility macro to initialize a pin control state.

This macro should be used in conjunction with PINCTRL_DT_STATE_PINS_DEFINE when using dynamic pin control to define an alternative state configuration stored in Devicetree.

Example:

// board.dts

/{
     zephyr,user {
             // uart0_alt_default node contains alternative pin config
             uart0_alt_default = <&uart0_alt_default>;
     };
};

// application

PINCTRL_DT_STATE_PINS_DEFINE(DT_PATH(zephyr_user), uart0_alt_default);

static const struct pinctrl_state uart0_alt[] = {
    PINCTRL_DT_STATE_INIT(uart0_alt_default, PINCTRL_STATE_DEFAULT)
};

See also

PINCTRL_DT_STATE_PINS_DEFINE

Parameters

prop – Property name in Devicetree containing state configuration.
state – State represented by prop (see PINCTRL_STATES).

Functions

int pinctrl_update_states(struct pinctrl_dev_config *config, const struct pinctrl_state *states, uint8_t state_cnt)

Update states with a new set.

Note

In order to guarantee device drivers correct operation the same states have to be provided. For example, if default and sleep are in the current list of states, it is expected that the new array of states also contains both.

Parameters

config – Pin control configuration.
states – New states to be set.
state_cnt – Number of new states to be set.

Return values

-EINVAL – If the new configuration does not contain the same states as the current active configuration.
-ENOSYS – If the functionality is not available.
0 – On success.

Other reference material

Introduction to pin muxing and GPIO control under Linux