atmel,sam0-uart

Description

These nodes are “uart” bus nodes.

Atmel SAM0 SERCOM UART driver

Properties

Properties not inherited from the base binding file.

Name	Type	Details
`rxpo`	`int`	Receive Data Pinout This property is required.
`txpo`	`int`	Transmit Data Pinout This property is required.
`collision-detection`	`boolean`	Enable collision detection for half-duplex mode.
`clock-frequency`	`int`	Clock frequency information for UART operation
`current-speed`	`int`	Initial baud rate setting for UART
`hw-flow-control`	`boolean`	Set to enable RTS/CTS flow control at boot time
`parity`	`string`	Configures the parity of the adapter. Enumeration id 0 for none, 1 for odd and 2 for even parity. Default to none if not specified. Legal values: `'none'`, `'odd'`, `'even'`
`pinctrl-0`	`phandles`	Pin configuration/s for the first state. Content is specific to the selected pin controller driver implementation.
`pinctrl-1`	`phandles`	Pin configuration/s for the second state. See pinctrl-0.
`pinctrl-2`	`phandles`	Pin configuration/s for the third state. See pinctrl-0.
`pinctrl-3`	`phandles`	Pin configuration/s for the fourth state. See pinctrl-0.
`pinctrl-4`	`phandles`	Pin configuration/s for the fifth state. See pinctrl-0.
`pinctrl-names`	`string-array`	Names for the provided states. The number of names needs to match the number of states.

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “atmel,sam0-uart” compatible.

Name	Type	Details
`reg`	`array`	register space This property is required. See Important properties for more information.
`interrupts`	`array`	interrupts for device This property is required. See Important properties for more information.
`clocks`	`phandle-array`	Clock gate information This property is required.
`clock-names`	`string-array`	name of each clock This property is required.
`dmas`	`phandle-array`	Optional TX & RX dma specifiers. Each specifier will have a phandle reference to the dmac controller, the channel number, and peripheral trigger source. For example dmas for TX, RX on SERCOM3 dmas = <&dmac 0 0xb>, <&dmac 0 0xa>;
`dma-names`	`string-array`	Required if the dmas property exists. This should be "tx" and "rx" to match the dmas property. For example dma-names = "tx", "rx";
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information.
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`power-domain`	`phandle`	Power domain the device belongs to. The device will be notified when the power domain it belongs to is either suspended or resumed.