nordic,nrf-qspi

Description

These nodes are “qspi” bus nodes.

Properties defining the interface for the Nordic QSPI peripheral.

The reg property describes two register blocks: one for the memory
corresponding to the QSPI peripheral registers, and another for
the memory mapped XIP area:

    qspi: qspi@2b000 {
            compatible = "nordic,nrf-qspi";
            reg = <0x2b000 0x1000>, <0x10000000 0x10000000>;
            reg-names = "qspi", "qspi_mm";
            ...
    };

Above, the register block with base address 0x2b000 and name
"qspi" are the QSPI peripheral registers. The register block with
base address 0x10000000 and name "qspi_mm" is the XIP area.

Properties

Properties not inherited from the base binding file.

Name	Type	Details
`io-pins`	`array`	IMPORTANT: This option will only be used if the new pin control driver is not enabled. Pin numbers associated with IO0 through IO3 signals. Examples: io-pins = <io0-pin io1-pin>; // two pins io-pins = <io0-pin io1-pin io2-pin io3-pin>; // four pins Either two or four pins must be configured using this property as shown above. The pin numbering scheme is the same as the sck-pin property's.
`csn-pins`	`array`	IMPORTANT: This option will only be used if the new pin control driver is not enabled. Chip select signal pin number. Exactly one pin should be given. The pin numbering scheme is the same as the sck-pin property's.
`pinctrl-0`	`phandles`	Pin configuration/s for the first state. Content is specific to the selected pin controller driver implementation.
`pinctrl-1`	`phandles`	Pin configuration/s for the second state. See pinctrl-0.
`pinctrl-2`	`phandles`	Pin configuration/s for the third state. See pinctrl-0.
`pinctrl-3`	`phandles`	Pin configuration/s for the fourth state. See pinctrl-0.
`pinctrl-4`	`phandles`	Pin configuration/s for the fifth state. See pinctrl-0.
`pinctrl-names`	`string-array`	Names for the provided states. The number of names needs to match the number of states.

Deprecated properties not inherited from the base binding file.

Name

Type

Details

sck-pin

int

IMPORTANT: This option will only be used if the new pin control driver
is not enabled.

The SCK pin to use.

For pins P0.0 through P0.31, use the pin number. For example,
to use P0.16 for SCK, set:

    sck-pin = <16>;

For pins P1.0 through P1.31, add 32 to the pin number. For
example, to use P1.2 for SCK, set:

    sck-pin = <34>;  /* 32 + 2 */

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nordic,nrf-qspi” compatible.

Name	Type	Details
`#address-cells`	`int`	number of address cells in reg property This property is required. Constant value: `1`
`#size-cells`	`int`	number of size cells in reg property This property is required.
`interrupts`	`array`	interrupts for device This property is required. See Important properties for more information.
`reg`	`array`	register space This property is required. See Important properties for more information.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information.
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`power-domain`	`phandle`	Power domain the device belongs to. The device will be notified when the power domain it belongs to is either suspended or resumed.