Wi-Fi: Shell

This sample allows you to test Nordic Semiconductor’s Wi-Fi chipsets.

Requirements

The sample supports the following development kit:

Hardware platforms

PCA

Board name

Build target

nRF7002 DK

PCA10143

nrf7002dk_nrf5340

nrf7002dk_nrf5340_cpuapp

Overview

This sample can perform all Wi-Fi operations in the 2.4GHz and 5GHz bands depending on the capabilities supported in the underlying chipset.

Using this sample, the development kit can associate with, and ping to, any Wi-Fi capable access point in STA mode.

Building and running

This sample can be found under samples/wifi/shell in the nRF Connect SDK folder structure.

When built as a non-secure firmware image for the _ns build target, the sample automatically includes the Trusted Firmware-M (TF-M).

See Building and programming an application for information about how to build and program the application and Testing and debugging an application for general information about testing and debugging in the nRF Connect SDK.

Currently, the following configurations are supported:

  • 7002 DK + QSPI

  • 7002 EK + SPIM

To build for the nRF7002 DK, use the nrf7002dk_nrf5340_cpuapp build target. The following is an example of the CLI command:

west build -b nrf7002dk_nrf5340_cpuapp

To build for the nRF7002 EK, use the nrf7002dk_nrf5340_cpuapp build target with the SHIELD CMake option set to nrf7002_ek. The following is an example of the CLI command:

west build -b nrf5340dk_nrf5340_cpuapp -- -DSHIELD=nrf7002_ek

See also Providing CMake options for instructions on how to provide CMake options.

Supported CLI commands

wifi is the Wi-Fi command line and supports the following UART CLI subcommands:

Wi-Fi shell subcommands

Subcommands

Description

scan

Scan for access points in the vicinity

connect
Connect to an access point with below parameters
<SSID>
<Passphrase> (optional: valid only for secured SSIDs)
<KEY_MGMT> (optional: 0-None, 1-WPA2, 2-WPA2-256, 3-WPA3)

disconnect

Disconnect from the current access point

status

Get the status of the Wi-Fi interface

statistics

Get the statistics of the Wi-Fi interface

ap_enable

Configure the Wi-Fi interface as access point mode

ap_disable

Configure the Wi-Fi interface as station mode

Testing

After programming the sample to your development kit, complete the following steps to test it:

  1. Connect the kit to the computer using a USB cable. The kit is assigned a COM port (Windows) or ttyACM device (Linux), which is visible in the Device Manager.

  2. Connect to the kit with a terminal emulator (for example, PuTTY). See How to connect with PuTTY for the required settings.

  3. Scan for the Wi-Fi networks in range using the following command:

    wifi scan

    The output should be similar to the following:

    Scan requested

Num  | SSID                             (len) | Chan | RSSI | Security        | BSSID
1    | xyza                             4     | 1    | -27  | WPA2-PSK        | xx:xx:xx:xx:xx:xx
2    | abcd                             4     | 1    | -28  | WPA2-PSK        | yy:yy:yy:yy:yy:yy

  4. Connect to your preferred network using the following command:

    wifi connect <SSID> <passphrase>

    <SSID> is the SSID of the network you want to connect to, and <passphrase> is its passphrase.

  5. Check the connection status after a while, using the following command:

    wifi status

    If the connection is established, you should see an output similar to the following:

    Status: successful
==================
State: COMPLETED
Interface Mode: STATION
Link Mode: WIFI 6 (802.11ax/HE)
SSID: OpenWrt
BSSID: C0:06:C3:1D:CF:9E
Band: 5GHz
Channel: 157
Security: WPA2-PSK
PMF: Optional
RSSI: 0

  6. Initiate a ping and verify data connectivity using the following commands:

    net dns <hostname>
net ping <resolved hostname>

    See the following example:

    net dns google.com
 Query for 'google.com' sent.
 dns: 142.250.74.46
 dns: All results received

net ping 10 142.250.74.46
 PING 142.250.74.46
 28 bytes from 142.250.74.46 to 192.168.50.199: icmp_seq=0 ttl=113 time=191 ms
 28 bytes from 142.250.74.46 to 192.168.50.199: icmp_seq=1 ttl=113 time=190 ms
 28 bytes from 142.250.74.46 to 192.168.50.199: icmp_seq=2 ttl=113 time=190 ms

Dependencies

This sample uses the following sdk-nrfxlib library:

This sample also uses modules that can be found in the following locations in the nRF Connect SDK folder structure:

  • modules/lib/hostap

  • modules/mbedtls