atmel-xplained-pro-header
Vendor: Generic or vendor-independent
Description
GPIO pins exposed on Atmel Xplained Pro headers.
The Xplained Pro layout provide a standard 20 pin header. A board can have
one or more headers and can share pins. The extension headers are given
names EXTn where n ϵ [1…7], n is determined by which ID pin is connected
to the embedded debugger. A header with ID7 signal from the embedded
debugger connected should be called EXT7. PWR, EXT1, EXT2 and EXT3 are
standard extension headers that have a predefined position according to the
list below:
* PWR is right angled at the top right hand side of the board. This
header must always be implemented.
* EXT1 is right angled at the top right hand side of the board, located
below the PWR header. This header must always be present.
* EXT2 is right angled and at the bottom right hand side of the board.
This header is mandatory for medium and large boards and should not be
implemented on small boards.
* EXT3 is right angled pointing downwards
All MCU boards have to implement at least PWR, EXT1, EXT2 (on medium and
large boards), and EXT3. EXT4 to EXT7 can be placed differently depending
on the board design. EXT4 to EXT7 can either be standard extension headers
or application specific headers.
Documentation:
* https://www.microchip.com/development-tools/xplained-boards
* http://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-42091-Atmel-Xplained-Pro-Hardware-Development-Kit_User%20Guide.pdf
This binding provides a nexus mapping for 20 pins where pins are disposed
to have a even and odd column:
Connector
Bind Pin Name Pin Pin Pin Name Bind
ID 1 2 GND
0 ADC(+) 3 4 ADC(-) 1
2 UART(RTS)/GPIO1 5 6 UART(CTS)/GPIO2 3
4 PWM(+) 7 8 PWM(-) 5
6 IRQ/GPIO3 9 10 SPI(CS1)/GPIO4 7
8 I2C(SDA) 11 12 I2C(SCL) 9
10 UART(RX) 13 14 UART(TX) 11
12 SPI(CS0) 15 16 SPI(MOSI) 13
14 SPI(MISO) 17 18 SPI(SCK) 15
GND 19 20 VDD(+3.3V)
Properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
This property is required. |
|
|
|
|
|
|
|
|
Number of items to expect in a GPIO specifier
This property is required. |
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “atmel-xplained-pro-header” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
register space
See Important properties for more information. |
|
|
name of each register space
|
|
|
interrupts for device
See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
Human readable string describing the device (used as device_get_binding() argument)
See Important properties for more information. |
|
|
Clock gate information
|
|
|
name of each clock
|
|
|
number of address cells in reg property
|
|
|
number of size cells in reg property
|
|
|
DMA channels specifiers
|
|
|
Provided names of DMA channel specifiers
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|