Secure Enclave solution for Trusted Firmware-M

Author: Mark Horvath
Organization: Arm Limited
Contact: Mark Horvath <mark.horvath@arm.com>

Abstract

This document summarizes the design goals and one possible implementation of the TF-M Secure Enclave solution.

Introduction

If a separate subsystem can provide the PSA Root of Trust (RoT) in a system then an additional physical separation exists between the most trusted and other domains. In such a system at least two subsystems are present, a Secure Enclave (SE) whose only task is to provide PSA RoT and an application core where any other application specific functionality can be placed. The latter core (or cores) are referred as Host in this document.

The current design assumes that Host is a v8-m core with security extension.

Requirements

Secure Enclave shall implement secure boot-flow (start-up first at reset and validate its own and the Host image or images before release Host from reset)
Secure Enclave shall provide the PSA RoT services
Host shall provide not just the non-secure context but the Application RoT as well
It shall be transparent to the (secure or non-secure) applications running on host whether the RoT services are provided by the same subsystem or by a Secure Enclave.

Note

In comparison, in a Dual Core system the whole secure context is placed on a separate subsystem, while a Secure Enclave only implements the PSA RoT security domain.

Proposed design

As the clients and the services are running on different cores only the IPC model can be used on both Secure Enclave and Host.

Secure Enclave

To provide the required functionality it is enough to run the current PSA RoT secure partitions on the Secure Enclave, so no need for non-secure context there. (It is enough if the Secure Enclave’s architecture is v6-m, v7-m or v8-m without the security extension.)

Secure Enclave can treat all clients running on Host as non-secure (even the services running on Host’s secure side). This means that fom Secure Enclave’s point of view all Host images, Host’s RAM and shared memory between Host and Secure Enclave if present are treated as non-secure. (Just like in the Dual CPU solution.) But the clients need to be distinguished, otherwise some functionalities are not working, for example: - Protected Storage partition shall run on Host, but the PS area is handled by Internal Trusted Storage partition (running on Secure Enclave). ITS partition decides whether it should work on PS or ITS assets by checking the client ID. - If a secure partition on host creates a crypto key, no other client shall be able to destroy it.

Communication

To communicate between Host and Secure Enclave, the existing mailbox solution can be reused as it is.

Host

On Host the current TF-M software architecture can be placed to provide non-secure context and Application RoT domain.

One solution to forward a PSA RoT IPC message from a client running on Host to the Secure Enclave is to add a proxy partition to the secure side. This PSA Proxy partition can provide all the RoT services to the system by forwarding the messages over the mailbox solution.

If the new partition’s manifest contains all the PSA RoT service IDs SPM will deliver all IPC messages there. Then the messages just must be blindly copied into the mailbox. PSA proxy can use the non-secure interface of the mailbox, but it is placed on the secure side of Host. (From SE’s point of view this is in fact the non-secure side of the mailbox as whole Host is treated as non-secure.)

It is important to verify IOVECs before forwarding them to SE, otherwise a malicous actor could use SE to access a memory area otherwise unaccessable. If PSA proxy uses the current secure partition interface then this is ensured by Host’s SPM.

SE treats all clients of Host as non-secure, so all PSA messages shall have a negative client ID when pushed into SE’s SPM. This is given for the clients on the non-secure side of Host, but the secure side clients of Host have positive client IDs. The straightforward solution is to translate the positive client IDs into a predefined negative range in PSA proxy, and push the translated values into the mailbox. Of course this range shall be reserved for this use only and no clients on non-secure side of Host shall have client ID from this range.

To avoid blocking Host when a message is sent PSA Proxy shall handle the service requests in non-blocking mode. And to maximize bandwidth PSA Proxy shall be able to push new messages into the mailbox, while others still not answered. To achieve these the mailbox interrupts needs to be handled in the PSA Proxy partition.