Application description

Overview
Requirements
Configuration
Building and running
Dependencies

The Serial LTE Modem (SLM) application demonstrates how to use the nRF9160 as a stand-alone LTE modem that can be controlled by AT commands.

Overview 

The nRF9160 SiP integrates both a full LTE modem and an application MCU, enabling you to run your LTE application directly on the nRF9160.

However, if you want to run your application on a different chip and use the nRF9160 only as a modem, the serial LTE modem application provides you with an interface for controlling the LTE modem through AT commands.

The application accepts both the modem-specific AT commands documented in the nRF91 AT Commands Reference Guide and the proprietary AT commands documented in the SLM-specific AT commands page.

Requirements 

The application supports the following development kits:

Hardware platforms	PCA	Board name	Build target
nRF9160 DK	PCA10090	nrf9160dk_nrf9160	`nrf9160dk_nrf9160_ns`
Thingy:91	PCA20035	thingy91_nrf9160	`thingy91_nrf9160_ns`

The sample is configured to compile and run as a non-secure application on nRF91’s Cortex-M33. Therefore, it automatically includes the Secure Partition Manager that prepares the required peripherals to be available for the application.

You can also configure it to use TF-M instead of Secure Partition Manager.

Configuration 

See Configuring your application for information about how to permanently or temporarily change the configuration.

Configuration options 

Check and configure the following configuration options for the sample:

CONFIG_SLM_CUSTOMIZED - Flag for customized functionality: This flag can be used to enable customized functionality. To add your own custom logic, enclose the code by #if defined(CONFIG_SLM_CUSTOMIZED) and enable this flag.

CONFIG_SLM_NATIVE_TLS - Use Zephyr mbedTLS: This option enables using Zephyr’s mbedTLS. It requires additional configuration. See Native TLS sockets for more information.

CONFIG_SLM_EXTERNAL_XTAL - Use external XTAL for UARTE: This option configures the application to use an external XTAL for UARTE. See the nRF9160 Product Specification (section 6.19 UARTE) for more information.

CONFIG_SLM_UART_HWFC_RUNTIME - Support of UART HWFC runtime configuration: This option let the application configure HWFC during runtime rather than while compiling by using #XSLMUART. This option is automatically selected when the rts-pin and cts-pin are defined in the DTS overlay.

CONFIG_SLM_CONNECT_UART_0 - UART 0

This option selects UART 0 for the UART connection. Select this option if you want to test the application with a PC.

This option is automatically selected when the build target is thingy91_nrf9160_ns.

CONFIG_SLM_CONNECT_UART_2 - UART 2: This option selects UART 2 for the UART connection. Select this option if you want to test the application with an external CPU.

CONFIG_SLM_START_SLEEP - Enter sleep on startup: This option makes nRF9160 enter deep sleep after startup. It is not selected by default.

CONFIG_SLM_INTERFACE_PIN - Interface GPIO to wake up from sleep or exit idle

This option specifies which interface GPIO to use for exiting sleep or idle mode. By default, P0.6 (Button 1 on the nRF9160 DK) is used when CONFIG_SLM_CONNECT_UART_0 is selected, and P0.31 is used when CONFIG_SLM_CONNECT_UART_2 is selected.

P0.26 (Multi-function button on Thingy:91) is used when the target is Thingy:91.

CONFIG_SLM_SOCKET_RX_MAX - Maximum RX buffer size for receiving socket data

This option specifies the maximum buffer size for receiving data through the socket interface. By default, this size is set to NET_IPV4_MTU (576), which is defined in Zephyr. The maximum value is 708, which is the maximum segment size (MSS) defined for the modem.

This option impacts the total RAM usage.

CONFIG_SLM_CR_TERMINATION - CR termination

This option configures the application to accept AT commands ending with a carriage return.

Select this option if you want to connect to the development kit using PuTTY. See How to connect with PuTTY for instructions.

CONFIG_SLM_LF_TERMINATION - LF termination: This option configures the application to accept AT commands ending with a line feed.

CONFIG_SLM_CR_LF_TERMINATION - CR+LF termination: This option configures the application to accept AT commands ending with a carriage return followed by a line feed.

CONFIG_SLM_TCP_POLL_TIME - Poll timeout in seconds for TCP connection: This option specifies the poll timeout for the TCP connection, in seconds.

CONFIG_SLM_SMS - SMS support in SLM: This option enables additional AT commands for using the SMS service.

CONFIG_SLM_GNSS - GNSS support in SLM: This option enables additional AT commands for using the GNSS service.

CONFIG_SLM_AGPS - nRF Cloud A-GPS support in SLM: This option enables additional AT commands for using the nRF Cloud A-GPS service. It is not selected by default.

CONFIG_SLM_PGPS - nRF Cloud P-GPS support in SLM: This option enables additional AT commands for using the nRF Cloud P-GPS service. It is not selected by default.

CONFIG_SLM_CELL_POS - nRF Cloud cellular positioning support in SLM: This option enables additional AT commands for using the nRF Cloud Cellular Positioning service. It is not selected by default.

CONFIG_SLM_FTPC - FTP client support in SLM: This option enables additional AT commands for using the FTP client service.

CONFIG_SLM_MQTTC - MQTT client support in SLM: This option enables additional AT commands for using the MQTT client service.

CONFIG_SLM_HTTPC - HTTP client support in SLM: This option enables additional AT commands for using the HTTP client service.

CONFIG_SLM_TWI - TWI support in SLM: This option enables additional AT commands for using the TWI service.

Additional configuration 

To save power, both the console and the output logs over UART_0 are disabled in this application. This information is logged using RTT instead. See Connecting using RTT for instructions on how to view this information.

To switch to UART output, change the following options in the prj.conf file:

# Segger RTT
CONFIG_USE_SEGGER_RTT=n
CONFIG_RTT_CONSOLE=n
CONFIG_UART_CONSOLE=y
CONFIG_LOG_BACKEND_RTT=n
CONFIG_LOG_BACKEND_UART=y

Configuration files 

The sample provides predefined configuration files for both the parent image and the child image. You can find the configuration files in the applications/nrf9160/serial_lte_modem directory.

The following configuration files are provided:

prj.conf - This configuration file contains the standard configuration for the serial LTE modem application.
overlay-native_tls.conf - This configuration file contains additional configuration options that are required to use Native TLS sockets. You can include it by adding -DOVERLAY_CONFIG=overlay-native_tls.conf to your build command. See Providing CMake options.
boards/nrf9160dk_nrf9160_ns.conf - Configuration file specific for the nRF9160 DK. This file is automatically merged with the prj.conf file when you build for the nrf9160dk_nrf9160_ns build target.
boards/thingy91_nrf9160_ns.conf - Configuration file specific for Thingy:91. This file is automatically merged with the prj.conf file when you build for the thingy91_nrf9160_ns build target.

In general, Kconfig overlays have an overlay- prefix and a .conf extension. Board-specific configuration files are named <BOARD>.conf and are located in the boards folder. DTS overlay files are named as the build target they are meant to be used with, and use the file extension .overlay. They are also placed in the boards folder. When the DTS overlay filename matches the build target, the overlay is automatically chosen and applied by the build system.

See Build and configuration system: for more information on the nRF Connect SDK configuration system.

Native TLS sockets 

By default, the secure socket (TLS/DTLS) is offloaded onto the modem. However, if you need customized TLS/DTLS features that are not supported by the modem firmware, you can use a native TLS socket instead. The serial LTE modem application will then handle all secure sockets used in TCP/IP, TCP/IP proxy, and MQTT.

If native TLS is enabled, the Credential storage management %CMNG command is overridden to map the security tag from the serial LTE modem application to the modem. You must use the overridden AT%CMNG command to provision the credentials to the modem.

Note

The Serial LTE Modem application supports security tags ranging from 0 to 214748364.

The configuration options that are required to enable the native TLS socket are defined in the overlay-native_tls.conf file.

Note

The following limitations exist for native TLS sockets:

PSK, PSK identity, and PSK public key are currently not supported.
The DTLS server is currently not supported.
AT%CMNG=1 is not supported.
The FTP and HTTP clients currently do not support native TLS.

Building and running 

This sample can be found under applications/nrf9160/serial_lte_modem in the nRF Connect SDK folder structure.

The sample is built as a non-secure firmware image for the nrf9160dk_nrf9160_ns build target. Because of this, it automatically includes the Secure Partition Manager. You can also configure it to use TF-M instead of SPM.

See Building and programming an application for information about how to build and program the application.

Communicating with the modem on the nRF9160 DK 

In this scenario, the nRF9160 DK running the Serial LTE Modem application serves as the host. You can use either a PC or an external MCU as a client.

Connecting with a PC 

To connect to the nRF9160 DK with a PC

Verify that CONFIG_SLM_CONNECT_UART_0 is defined in the application. It is defined in the default configuration.
Use LTE Link Monitor to connect to the development kit. See How to connect with LTE Link Monitor for instructions. You can then use this connection to send or receive AT commands over UART, and to see the log output of the development kit.

Alternatively, you can use a terminal emulator like Termite, Teraterm, or PuTTY to establish a terminal connection to the development kit, using the following settings:
- Baud rate: 115200
- 8 data bits
- 1 stop bit
- No parity
- HW flow control: None
Note

The default AT command terminator is a carriage return followed by a line feed (\r\n). LTE Link Monitor supports this format. If you want to use another terminal emulator, make sure that the configured AT command terminator corresponds to the line terminator of your terminal.

When using Termite and Teraterm, configure the AT command terminator as follows:

When using PuTTY, you must set the CONFIG_SLM_CR_TERMINATION SLM configuration option instead. See application configuration for more details.

Connecting with an external MCU 

Note

This section does not apply to Thingy:91 as it does not have UART2.

If you run your user application on an external MCU (for example, an nRF52 Series development kit), you can control the modem on nRF9160 directly from the application. See the nRF52 client for Serial LTE Modem application repository for a sample implementation of such an application.

To connect with an external MCU, set the CONFIG_UART_2_NRF_HW_ASYNC_TIMER and CONFIG_SLM_CONNECT_UART_2 configuration options in the Serial LTE Modem application configuration.

The following table shows how to connect an nRF52 Series development kit to the nRF9160 DK to be able to communicate through UART:

nRF52 Series DK	nRF9160 DK
UART TX P0.6	UART RX P0.11
UART RX P0.8	UART TX P0.10
UART CTS P0.7	UART RTS P0.12
UART RTS P0.5	UART CTS P0.13
GPIO OUT P0.27	GPIO IN P0.31

Use the following UART instances:

nRF52840 or nRF52832 - UART0
nRF9160 - UART2

Use the following UART configuration:

Hardware flow control: enabled
Baud rate: 115200
Parity bit: no
Operation mode: IRQ

Note

The GPIO output level on the nRF9160 side must be 3 V. You can set the VDD voltage with the VDD IO switch (SW9). See the VDD supply rail section in the nRF9160 DK User Guide for more information.

Communicating with the modem on Thingy:91 

In this scenario, Thingy:91 running the Serial LTE Modem application serves as the host. You can use only a PC as a client.

Connecting with a PC 

To connect to Thingy:91 with a PC, you must first program the Connectivity bridge on the nrf52840 of Thingy:91. It routes UART_0 to USB_CDC0 on Thingy:91. By enabling the option CONFIG_BRIDGE_BLE_ENABLE , you can also use SLM over Nordic UART Service (NUS).

Then follow the instructions below:

Verify that CONFIG_SLM_CONNECT_UART_0 is defined in the application. It is defined in the default configuration.
Use LTE Link Monitor to connect to the development kit. See How to connect with LTE Link Monitor for instructions. You can then use this connection to send or receive AT commands over UART, and to see the log output of the development kit.

Alternatively, you can use a terminal emulator like Termite, Teraterm, or PuTTY to establish a terminal connection to the development kit, using the following settings:
- Baud rate: 115200
- 8 data bits
- 1 stop bit
- No parity
- HW flow control: None
Note

The default AT command terminator is a carriage return followed by a line feed (\r\n). LTE Link Monitor supports this format. If you want to use another terminal emulator, make sure that the configured AT command terminator corresponds to the line terminator of your terminal.

When using Termite and Teraterm, configure the AT command terminator as follows:

When using PuTTY, you must set the CONFIG_SLM_CR_TERMINATION SLM configuration option instead. See application configuration for more details.

You can also test the i2c sensor on Thingy:91 using TWI AT commands. See TWI AT commands for more details.

Testing 

The following testing instructions focus on testing the application with a PC client. If you have an nRF52 Series DK running a client application, you can also use this DK for testing the different scenarios.

After programming the sample to your development kit, test it by performing the following steps:

Connect the kit to the computer using a USB cable. The kit is assigned a COM port (Windows) or ttyACM device (Linux), which is visible in the Device Manager.
Connect to the kit with LTE Link Monitor. If you want to use a different terminal emulator, see slm_connecting_9160dk_pc.
Reset the kit.
Observe that the development kit sends a Ready\r\n message on UART.
Enter AT+CFUN=1 to turn on the modem and connect to the network.
Enter AT+CFUN? and observe that the connection indicators in the LTE Link Monitor side panel turn green. This indicates that the modem is connected to the network.
Send AT commands and observe the responses from the development kit.

See Testing scenarios for typical test cases.

Dependencies 

This application uses the following nRF Connect SDK libraries:

It uses the following sdk-nrfxlib libraries:

Modem library

In addition, it uses the following samples:

Secure Partition Manager