CONFIG_I2S_STM32_PLLI2S_PLLR

Division factor for I2S clock

Type: int

Help

Division factor for the I2S clock.
PLLR factor should be selected to ensure that the I2S clock
frequency is less than or equal to 192MHz.
Allowed values: 2-7

Direct dependencies

(I2S && BOARD_NUCLEO_F411RE) || (I2S && BOARD_NUCLEO_F411RE) || (I2S && BOARD_96B_ARGONKEY) || (I2S && BOARD_96B_STM32_SENSOR_MEZ) || (I2S && BOARD_NUCLEO_F411RE) || (I2S_STM32_USE_PLLI2S_ENABLE && I2S_STM32 && I2S)

(Includes any dependencies from ifs and menus.)

Defaults

• 3

• 3

• 3

• 3

• 3

• 7

Kconfig definitions

At <Zephyr>/boards/shields/x_nucleo_iks02a1/boards/nucleo_f411re.defconfig:40

Included via <Zephyr>/Kconfig:8 → <Zephyr>/Kconfig.zephyr:18 → <nRF>/doc/_build/kconfig/Kconfig.shield.defconfig:1 → <Zephyr>/boards/shields/x_nucleo_iks02a1/Kconfig.defconfig:5

Menu path: (Top)

config I2S_STM32_PLLI2S_PLLR
    int
    default 3
    depends on I2S && BOARD_NUCLEO_F411RE

---

At <Zephyr>/boards/shields/x_nucleo_iks02a1/boards/nucleo_f411re.defconfig:40

Included via <Zephyr>/Kconfig:8 → <Zephyr>/Kconfig.zephyr:20 → <Zephyr>/boards/shields/x_nucleo_iks02a1/Kconfig.defconfig:5

Menu path: (Top)

config I2S_STM32_PLLI2S_PLLR
    int
    default 3
    depends on I2S && BOARD_NUCLEO_F411RE

---

At <Zephyr>/boards/arm/96b_argonkey/Kconfig.defconfig:23

Included via <Zephyr>/Kconfig:8 → <Zephyr>/Kconfig.zephyr:22

Menu path: (Top)

config I2S_STM32_PLLI2S_PLLR
    int
    default 3
    depends on I2S && BOARD_96B_ARGONKEY

---

At <Zephyr>/boards/arm/96b_stm32_sensor_mez/Kconfig.defconfig:23

Included via <Zephyr>/Kconfig:8 → <Zephyr>/Kconfig.zephyr:22

Menu path: (Top)

config I2S_STM32_PLLI2S_PLLR
    int
    default 3
    depends on I2S && BOARD_96B_STM32_SENSOR_MEZ

---

At <Zephyr>/boards/shields/x_nucleo_iks02a1/boards/nucleo_f411re.defconfig:40

Included via <Zephyr>/Kconfig:8 → <Zephyr>/Kconfig.zephyr:22 → <Zephyr>/boards/shields/x_nucleo_iks02a1/Kconfig.defconfig:5

Menu path: (Top)

config I2S_STM32_PLLI2S_PLLR
    int
    default 3
    depends on I2S && BOARD_NUCLEO_F411RE

---

At <Zephyr>/drivers/i2s/Kconfig.stm32:53

Included via <Zephyr>/Kconfig:8 → <Zephyr>/Kconfig.zephyr:42 → <Zephyr>/drivers/Kconfig:44 → <Zephyr>/drivers/i2s/Kconfig:28

Menu path: (Top) → Device Drivers → I2S bus drivers → STM32 MCU I2S controller driver → Enable usage of PLL

config I2S_STM32_PLLI2S_PLLR
    int "Division factor for I2S clock"
    range 2 7
    default 7
    depends on I2S_STM32_USE_PLLI2S_ENABLE && I2S_STM32 && I2S
    help
      Division factor for the I2S clock.
      PLLR factor should be selected to ensure that the I2S clock
      frequency is less than or equal to 192MHz.
      Allowed values: 2-7

(The ‘depends on’ condition includes propagated dependencies from ifs and menus.)