Telink TLSR9518ADK80D¶

Overview¶

The TLSR9518A Generic Starter Kit is a hardware platform which can be used to verify the Telink TLSR9 series chipset 1 and develop applications for several 2.4 GHz air interface standards including Bluetooth 5.2 (Basic data rate, Enhanced data rate, LE, Indoor positioning and BLE Mesh), Zigbee 3.0, Homekit, 6LoWPAN, Thread and 2.4 Ghz proprietary.

More information about the board can be found at the Telink B91 Generic Starter Kit Hardware Guide 2 website.

Hardware¶

The TLSR9518A SoC integrates a powerful 32-bit RISC-V MCU, DSP, AI Engine, 2.4 GHz ISM Radio, 256 KB SRAM (128 KB of Data Local Memory and 128 KB of Instruction Local Memory), external Flash memory, stereo audio codec, 14 bit AUX ADC, analog and digital Microphone input, PWM, flexible IO interfaces, and other peripheral blocks required for advanced IoT, hearable, and wearable devices.

The TLSR9518ADK80D default board configuration provides the following hardware components:

RF conducted antenna
1 MB External Flash memory with reset button
Chip reset button
Mini USB interface
4-wire JTAG
4 LEDs, Key matrix up to 4 keys
2 line-in function (Dual Analog microphone supported when switching jumper from microphone path)
Dual Digital microphone
Stereo line-out

Supported Features¶

The Zephyr TLSR9518ADK80D board configuration supports the following hardware features:

Interface	Controller	Driver/Component
PLIC	on-chip	interrupt_controller
RISC-V Machine Timer (32 KHz)	on-chip	timer
PINMUX	on-chip	pinmux
GPIO	on-chip	gpio
UART	on-chip	serial

The following example projects are supported:

samples/hello_world
samples/synchronization
samples/philosophers
samples/basic/threads
samples/basic/blinky
samples/basic/button
samples/subsys/console/echo
samples/subsys/console/getchar
samples/subsys/console/getline
samples/subsys/shell/shell_module
samples/subsys/cpp/cpp_synchronization

Note

To support “button” example project PC3-KEY3 (J20-19, J20-20) jumper needs to be removed and KEY3 (J20-19) should be connected to VDD3_DCDC (J51-13) externally.

For the rest example projects use the default jumpers configuration.

Other hardware features and example projects are not supported yet.

Limitations¶

Maximum 3 GPIO pins could be configured to generate interrupts simultaneously. All pins must be related to different ports and use different IRQ numbers.
DMA mode is not supported by Serial Port.
UART hardware flow control is not implemented.

Default configuration and IOs¶

System Clock¶

The TLSR9518ADK80D board is configured to use the 24 MHz external crystal oscillator with the on-chip PLL/DIV generating the 48 MHz system clock. The following values also could be assigned to the system clock in the board DTS file (boards/riscv/tlsr9518adk80d/tlsr9518adk80d.dts):

16000000
24000000
32000000
48000000
64000000
96000000

&cpu0 {
    clock-frequency = <48000000>;
};

PINs Configuration¶

The TLSR9518A SoC has five GPIO controllers (PORT_A to PORT_E), but only two are currently enabled (PORT_B for LEDs control and PORT_C for buttons) in the board DTS file:

LED0 (blue): PB4, LED1 (green): PB5, LED2 (white): PB6, LED3 (red): PB7
Key Matrix SW0: PC2_PC3, SW1: PC2_PC1, SW2: PC0_PC3, SW3: PC0_PC1

Peripheral’s pins on the SoC are mapped to the following GPIO pins in the boards/riscv/tlsr9518adk80d/tlsr9518adk80d.dts file:

UART0 RX: PB2, TX: PB3
UART1 RX: PC6, TX: PC7

Serial Port¶

The TLSR9518A SoC has 2 UARTs. The Zephyr console output is assigned to UART0 in the boards/riscv/tlsr9518adk80d/tlsr9518adk80d_defconfig file. The default settings are 115200 8N1.

Programming and debugging¶

Building¶

You can build applications in the usual way. Here is an example for the “hello_world” application.

# From the root of the zephyr repository
west build -b tlsr9518adk80d samples/hello_world

To use Telink RISC-V Linux Toolchain 3, ZEPHYR_TOOLCHAIN_VARIANT and CROSS_COMPILE variables need to be set.

# Set Zephyr toolchain variant to cross-compile
export ZEPHYR_TOOLCHAIN_VARIANT=cross-compile
# Specify the Telink RISC-V Toolchain location
export CROSS_COMPILE=~/toolchains/nds32le-elf-mculib-v5f/bin/riscv32-elf-
# From the root of the zephyr repository
west build -b tlsr9518adk80d samples/hello_world

Telink RISC-V Linux Toolchain 3 is available on the Burning and Debugging Tools for TLSR9 Series in Linux 6 page.

Open a serial terminal with the following settings:

Speed: 115200
Data: 8 bits
Parity: None
Stop bits: 1

Flash the board, reset and observe the following messages on the selected serial port:

*** Booting Zephyr OS version 2.5.0  ***
Hello World! tlsr9518adk80d

Flashing¶

In order to flash the TLSR9518ADK80D board check the following resources:

Debugging¶

Supporting UART debug and OpenOCD+GDB.

References¶

1: http://wiki.telink-semi.cn/wiki/chip-series/TLSR9-Series/
2: http://wiki.telink-semi.cn/wiki/Hardware/B91_Generic_Starter_Kit_Hardware_Guide/
3(1,2): http://wiki.telink-semi.cn/tools_and_sdk/Tools/IDE/telink_riscv_linux_toolchain.zip
4: http://wiki.telink-semi.cn/wiki/IDE-and-Tools/Burning-and-Debugging-Tools-for-all-Series/
5: http://wiki.telink-semi.cn/wiki/IDE-and-Tools/Burning-and-Debugging-Tools-for-TLSR9-Series/
6(1,2): http://wiki.telink-semi.cn/wiki/IDE-and-Tools/BDT_for_TLSR9_Series_in_Linux/