Bluetooth: Direct Test Mode

This sample enables the Direct Test Mode functions described in Bluetooth Core Specification: Version 5.2, Vol. 6, Part F.

Overview

The sample uses Direct Test Mode (DTM) to test the operation of the following features of the radio:

  • Transmission power and receiver sensitivity

  • Frequency offset and drift

  • Modulation characteristics

  • Packet error rate

  • Intermodulation performance

Test procedures are defined in the document Bluetooth Low Energy RF PHY Test Specification: Document number RF-PHY.TS.p15

You can carry out conformance tests using dedicated test equipment, such as the Anritsu MT8852 or similar, with an nRF5 running the DTM sample set as device under test (DUT).

DTM sample

The DTM sample includes two parts:

  • The DTM, Direct Test Mode library, which manages the nRF radio and controls the standard DTM procedures.

  • A sample that provides an external interface to the library.

You can find the source code of both parts here: samples/bluetooth/direct_test_mode/src.

The DTM sample contains a driver for a 2-wire UART interface. The driver maps two-octet commands and events to the DTM library, as specified by the Bluetooth Low Energy DTM specification.

nRF5 with DTM as a DUT

The implementation is self-contained and requires no Bluetooth Low Energy protocol stack for its operation. The MPU is initialized in the standard way. The DTM library function dtm_init configures all interrupts, timers, and the radio.

main.c may be replaced with other interface implementations, such as an HCI interface, USB, or another interface required by the Upper Tester.

The interface to the Lower Tester uses the antenna connector of the chosen development kit. While in principle an aerial connection might be used, conformance tests cover the reading of the transmission power delivered by the DUT. For this reason, a coaxial connection between the DUT and the Lower Tester is employed for all conformance testing.

DTM module interface

The DTM function dtm_cmd_put implements the four commands defined by the Bluetooth Low Energy standard:

  • TEST SETUP (called RESET in Bluetooth 4.0)

  • RECEIVER_TEST

  • TRANSMITTER_TEST

  • TEST_END

In the dtm_cmd_put interface, DTM commands are accepted in the 2-byte format. Parameters such as: CMD code, Frequency, Length, or Packet Type are encoded within this command.

The following DTM events are polled using the dtm_event_get function:

  • PACKET_REPORTING_EVENT

  • TEST_STATUS_EVENT [ SUCCESS | FAIL ]

State machine overview of the DTM

Supported PHYs

The DTM sample supports all four PHYs specified in DTM, but not all devices support all the PHYs.

Supported PHYs

PHY

nRF5340

LE 1M

Yes

LE 2M

Yes

LE Coded S=8

Yes

LE Coded S=2

Yes

Bluetooth Direction Finding support

The DTM sample supports all Bluetooth Direction Finding modes specified in DTM.

Supported Bluetooth Direction Finding modes

Direction Finding mode

nRF5340

AoD 1 us slot

Yes

AoD 2 us slot

Yes

AoA

Yes

The following antenna switching patterns are possible:

  • 1, 2, 3, …, N

  • 1, 2, 3, …, N, N - 1, N - 2, …, 1

The application supports a maximum of 19 antennas in the direction finding mode. The RADIO can control up to 8 GPIO pins for the purpose of controlling the external antenna switches used in direction finding.

The antenna is chosen by writing consecutive numbers to the SWITCHPATTERN register. This means that the antenna GPIO pins act like 8-bit registers. In other words, for the first antenna, antenna pin 1 is active, for the second antenna, pin 2 is active, for the third antenna, pins 1 and 2 are active, and so on.

nRF21540 front-end module

You can add support for the nRF21540 front-end module (FEM) to the sample. Set -DNRF21540EK_FEM=y when you invoke west build or cmake in your sample directory. Follow the instructions in Providing CMake options. For example:

west build -b nrf5340dk_nrf5340_cpunet -- -DNRF21540EK_FEM=y

When you set NRF21540EK_FEM=y the dts-nrf21540-fem.overlay devicetree overlay file is used to override the default settings. The configuration from this file is merged with the additional development kit overlay file from the boards folder if it exists.

The dts-nrf21540-fem.overlay is located in the samples/bluetooth/direct_test_mode/configuration folder. Make sure that the GPIOs and the SPI configuration in the file correspond to those in which your front-end module is connected.

Note

You must set NRF21540EK_FEM=y if you use the nRF21540 EK. If you use the nRF21540 DK, build your application for the nrf21540dk_nrf52840 board. The devicetree for the nRF21540 DK already contains the required FEM configuration, so you do not need to set an additional build option.

Sometimes, you may need to add an extra overlay file. The easiest way to add the file when building is to set it in the DTC_OVERLAY_FILE variable. However, that will override the default settings. When you set the DTC_OVERLAY_FILE variable, you must specify all overlay files that are needed for building.

Follow the instructions in Providing CMake options to specify the DTC_OVERLAY_FILE variable. For example, to build the sample from the command line for an nRF5340 DK with an attached nRF21540 EK, invoke the following command within the sample directory: west build -b nrf5340dk_nrf5340_cpunet -- -DDTC_OVERLAY_FILE="boards/nrf5340dk_nrf5340_cpunet.overlay;../configuration/dts-nrf21540-fem.overlay;your_overlay_file.overlay"

See Set devicetree overlays for different ways of adding the overlay file.

Alternatively, you can copy the contents of dts-nrf21540-fem.overlay to the board’s overlay file.

Note

The nRF5340 DK network core peripherals, like UART and SPI, share an ID and a base address. To configure the nRF21540 front-end module gain, write the gain value over the SPI. In samples, UART is used as a control interface or shell transport. To send the gain value UART is temporary disabled and restarted after the SPI transfer.

You can configure the transmitted power gain and activation delay in nRF21540 using vendor-specific commands, see Vendor-specific packet payload.

Vendor-specific packet payload

The Bluetooth Low Energy 2-wire UART DTM interface standard reserves the Packet Type, also called payload parameter, with binary value 11 for a Vendor Specific packet payload.

The DTM command is interpreted as a Vendor-Specific one when both the following conditions are met:

  • Its CMD field is set to Transmitter Test, binary 10.

  • Its PKT field is set to Vendor-Specific, binary 11.

Vendor specific commands can be divided into different categories as follows:

  • If the Length field is set to 0 (symbol CARRIER_TEST), an unmodulated carrier is turned on at the channel indicated by the Frequency field. It remains turned on until a TEST_END or RESET command is issued.

  • If the Length field is set to 1 (symbol CARRIER_TEST_STUDIO), this field value is used by the nRFgo Studio to indicate that an unmodulated carrier is turned on at the channel. It remains turned on until a TEST_END or RESET command is issued.

  • If the Length field is set 2 (symbol SET_TX_POWER), the Frequency field sets the TX power in dBm. The valid TX power values are specified in the product specification ranging from -40 to +4. 0 dBm is the reset value. Only the 6 least significant bits will fit in the Length field. The two most significant bits are calculated by the DTM module. This is possible because the 6 least significant bits of all valid TX power values are unique. The TX power can be modified only when no Transmitter Test or Receiver Test is running.

  • If the Length field is set to 3``(symbol ``NRF21540_ANTENNA_SELECT), the Frequency field sets the nRF21540 FEM antenna. The valid values are:

    • 0 - ANT1 enabled, ANT2 disabled

    • 1 - ANT1 disabled, ANT2 enabled

  • If the Length field is set to 4 (symbol NRF21540_GAIN_SET), the Frequency field sets the nRF21540 FEM TX gain value in arbitrary units. The valid gain values are specified in the nRF21540 product-specific range from 0 to 31.

  • If the Length field is set to 5 (symbol NRF21540_ACTIVE_DELAY_SET), the Frequency field sets the nRF21540 FEM activation delay in microseconds relative to a radio start. By default, this value is set to (radio ramp-up time - nRF21540 TX/RX settling time).

  • All other values of Frequency and Length field are reserved.

The DTM-to-Serial adaptation layer

main.c is an implementation of the UART interface specified in the Bluetooth Core Specification: Vol. 6, Part F, Chap. 3.

The default selection of UART pins is defined in zephyr/boards/arm/board_name/board_name.dts. You can change the defaults using the symbols tx-pin and rx-pin in the DTS overlay file at the project level.

Debugging

In this sample, the UART console is used to exchange commands and events defined in the DTM specification. Debug messages are not displayed in this UART console. Instead, they are printed by the RTT logger.

If you want to view the debug messages, follow the procedure in Connecting via RTT.

Requirements

The sample supports the following development kit:

Hardware platforms

PCA

Board name

Build target

nRF5340 DK

PCA10095

nrf5340dk_nrf5340

nrf5340dk_nrf5340_cpunet

nRF21540 DK

PCA10112

nrf21540dk_nrf52840

nrf21540dk_nrf52840

Additionally, the sample requires one of the following testing devices:

Building and running

This sample can be found under samples/bluetooth/direct_test_mode in the nRF Connect SDK folder structure.

See Building and programming a sample application for information about how to build and program the application.

Note

On the nRF5340 development kit, the Direct Test Mode sample is a standalone network sample. It does not require any counterpart application sample. However, you must still program the application core to boot up the network core. You can use any sample for this, for example, the nRF5340: Empty firmware for application core.

Testing

After programming the sample to your development kit, you can test it in the three following ways.

Note

For the nRF5340 DK board (PCA10095), see Getting logging output for information about the COM terminals on which the logging output is available.

Testing with a certified tester

Conformance testing is done using a certified tester. The setup depends on the tester used, and details about the test operation must be found in the tester documentation.

Application note nAN34 describes two alternatives for setting up a production test with DTM using one of our old devices.

Testing with another development kit

  1. Connect both development kits to the computer using a USB cable. The computer assigns to the development kit a COM port on Windows or a ttyACM device on Linux, which is visible in the Device Manager.

  2. Connect to both kits with a terminal emulator. See Direct Test Mode terminal connection for the required settings.

  3. Start TRANSMITTER_TEST by sending the 0x80 0x96 DTM command to one of the connected development kits. This command will trigger TX activity on the 2402 MHz frequency (1st channel) with 10101010 packet pattern and 37-byte packet length.

  4. Observe that you received the TEST_STATUS_EVENT packet in response with the SUCCESS status field: 0x00 0x00.

  5. Start RECEIVER_TEST by sending the 0x40 0x96 DTM command to the second development kit. Command parameters are identical to the ones used for the TRANSMITTER_TEST command.

  6. Observe that you received the TEST_STATUS_EVENT packet in response with the SUCCESS status field: 0x00 0x00.

  7. Finish RX testing using the TEST_END DTM command by sending the 0xC0 0x00 packet.

  8. Observe that you received the PACKET_REPORTING_EVENT packet in response. For example, the 0xD6 0xAC message indicates that 22188 Radio packets have been received.

  9. Experiment with other combinations of commands and their parameters.

Testing with nRF Connect for Desktop

  1. Connect the development kit to the computer using a USB cable. The computer assigns to the development kit a COM port on Windows or a ttyACM device on Linux, which is visible in the Device Manager.

  2. Connect to the kit with a terminal emulator. See Direct Test Mode terminal connection for the required settings.

  3. Start the TRANSMITTER_TEST by sending the 0x80 0x96 DTM command to the connected development kit. This command triggers TX activity on 2402 MHz frequency (1st channel) with 10101010 packet pattern and 37-byte packet length.

  4. Observe that you received the TEST_STATUS_EVENT packet in response with the SUCCESS status field: 0x00 0x00.

  5. Start the Direct Test Mode application in nRF Connect for Desktop and select the development kits to communicate with.

  6. Set the Receiver mode and 37th channel in the test configuration menu.

  7. Start the test.

  8. On the application chart, observe that the number of RX packets is increasing for the 2402 MHz channel.

  9. Stop the test.

  10. Swap roles. Set the application to the RX mode and the connected development kit to the TX mode.

Direct Test Mode terminal connection

To send commands to and receive responses from the development kit that runs the Direct Test Mode sample, connect to it with RealTerm in Windows or Minicom in Linux.

The Bluetooth Low Energy DTM UART interface standard specifies the following configuration:

  • Eight data bits

  • No parity

  • One stop bit

  • No hardware flow control

  • A selection of bit rates from 9600 to 1000000, one of which must be supported by the DUT. It might be possible to run other bit rates by experimenting with parameters.

Note

The default bit rate of the DTM UART driver is 19200 bps, which is supported by most certified testers.

You must send all commands as two-byte HEX numbers. The responses must have the same format.

Connect with RealTerm (Windows)

The RealTerm terminal program offers a graphical interface for setting up your connection.

RealTerm start window

The RealTerm start window

To test DTM with RealTerm, complete the following steps:

  1. On the Display tab, set Display As to Hex[space].

    Set the RealTerm display format
  2. Open the Port tab and configure the serial port parameters:

    1. Set the Baud to 19200 (1).

    2. Select your J-Link serial port from the Port list (2).

    3. Set the port status to “Open” (3).

    RealTerm serial port settings
  3. Open the Send tab:

    1. Write the command as a hexadecimal number in the field (1). For example, write 0x00 0x00 to send a Reset command.

    2. Click the Send Numbers button (2) to send the command.

    3. Observe the response in the DTM in area (3). The response is encoded as hexadecimal numbers.

    RealTerm commands sending
Connect with Minicom (Linux)

Minicom is a serial communication program that connects to the DTM device.

On the Linux operating system, install a Minicom terminal. On Ubuntu, run:

sudo apt-get install minicom
  1. Run the Minicom terminal:

    sudo minicom -D DTM serial port -s

    For example:

    sudo minicom -D /dev/serial/by-id/usb-SEGGER_J-Link_000683580193-if00 -s
    

    The -s option switches you to Minicom setup mode.

  2. Configure the Minicom terminal:

    minicom configuration window

    Configuration window

    1. Select Serial port setup and set UART baudrate to 19200.

      minicom serial port settings
    2. Select Screen and keyboard and press S on the keyboard to enable the Hex Display.

    3. Press Q on the keyboard to enable Local echo.

      minicom terminal screen and keyboard settings

    Minicom is now configured for receiving data. However, you cannot use it for sending DTM commands.

  3. Send DTM commands:

    To send DTM commands, use echo with -ne options in another terminal. You must encode the data as hexadecimal numbers (xHH, byte with hexadecimal value HH, 1 to 2 digits).

    sudo echo -ne "encoded command" > DTM serial port

    To send a Reset command, for example, run the following command:

    sudo echo -ne "\x00\x00" > /dev/serial/by-id/usb-SEGGER_J-Link_000683580193-if00
    

Dependencies

This sample uses the following nrfx dependencies:

  • nrfx/drivers/include/nrfx_timer.h

  • nrfx/hal/nrf_nvmc.h

  • nrfx/hal/nrf_radio.h

  • nrfx/helpers/nrfx_gppi.h

In addition, it uses the following Zephyr libraries: