solomon,ssd1306fb (on spi bus)

Vendor: Solomon Systech Limited

Description

SSD1306 128x64 dot-matrix display controller on SPI bus

Properties

Properties not inherited from the base binding file.

Name

Type

Details

data_cmd-gpios

phandle-array

D/C# pin.

This property is required.

segment-offset

int

8-bit column start address for Page Addressing Mode

This property is required.

page-offset

int

Start address for Page Addressing Mode

This property is required.

display-offset

int

mapping of the display start line to one of COM0 .. COM63

This property is required.

multiplex-ratio

int

Multiplex Ratio

This property is required.

segment-remap

boolean

Last column address is mapped to first segment

com-invdir

boolean

Scan direction is from last COM output to first COM output

com-sequential

boolean

Sequential COM pin configuration

prechargep

int

Duration of the pre-charge period

This property is required.

reset-gpios

phandle-array

RESET pin.
The RESET pin of SSD1306 is active low. If connected directly the MCU pin should be configured as active low.

inversion-on

boolean

Turn on display color inverting

ready-time-ms

int

Time it takes for the device from power up to become responsive and
accepting commands. Defaults to 10ms (found by trial and error) if not
provided.

Default value: 10

height

int

Height of the panel driven by the controller, with the units in pixels.

This property is required.

width

int

Width of the panel driven by the controller, with the units in pixels.

This property is required.

spi-max-frequency

int

Maximum clock frequency of device's SPI interface in Hz

This property is required.

duplex

int

Duplex mode, full or half. By default it's always full duplex thus 0
as this is, by far, the most common mode.
Use the macros not the actual enum value, here is the concordance
list (see dt-bindings/spi/spi.h)
  0    SPI_FULL_DUPLEX
  2048 SPI_HALF_DUPLEX

Legal values: 0, 2048

frame-format

int

Motorola or TI frame format. By default it's always Motorola's,
thus 0 as this is, by far, the most common format.
Use the macros not the actual enum value, here is the concordance
list (see dt-bindings/spi/spi.h)
  0     SPI_FRAME_FORMAT_MOTOROLA
  32768 SPI_FRAME_FORMAT_TI

Legal values: 0, 32768

spi-cpol

boolean

SPI clock polarity which indicates the clock idle state.
If it is used, the clock idle state is logic high; otherwise, low.

spi-cpha

boolean

SPI clock phase that indicates on which edge data is sampled.
If it is used, data is sampled on the second edge; otherwise, on the first edge.

spi-hold-cs

boolean

In some cases, it is necessary for the master to manage SPI chip select
under software control, so that multiple spi transactions can be performed
without releasing it. A typical use case is variable length SPI packets
where the first spi transaction reads the length and the second spi transaction
reads length bytes.

supply-gpios

phandle-array

GPIO specifier that controls power to the device.

This property should be provided when the device has a dedicated
switch that controls power to the device.  The supply state is
entirely the responsibility of the device driver.

Contrast with vin-supply.

vin-supply

phandle

Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.

This property should be provided when device power is supplied
by a shared regulator.  The supply state is dependent on the
request status of all devices fed by the regulator.

Contrast with supply-gpios.  If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.