:orphan:
.. raw:: html
.. dtcompatible:: nordic,nrf-twi
.. _dtbinding_nordic_nrf_twi:
nordic,nrf-twi
##############
Vendor: :ref:`Nordic Semiconductor `
Description
***********
These nodes are "i2c" bus nodes.
.. code-block:: none
Nordic nRF family TWI (TWI master).
This binding can be used for nodes which can represent TWI
peripherals. When a single SoC peripheral ID corresponds to multiple
I2C peripherals (like TWI or TWIM), the corresponding devicetree
nodes must be set up to select TWI before use.
To select TWI, set the node's "compatible" to "nordic,nrf-twi" and
its "status" to "okay", e.g. using an overlay file like this:
/* This is for TWI0 -- change to "i2c1" for TWI1. */
&i2c0 {
compatible = "nordic,nrf-twi";
status = "okay";
/* other property settings can go here */
};
You can use either of these options to check TWI availability on
your SoC:
1. Check the peripheral Instantiation table in the Memory
section of your SoC's Product Specification document.
A "TWI0" instance in the table means "i2c0" in the devicetree
can be used with this binding, and similarly for "TWI1".
2. Open your SoC's .dtsi file and look for a node definition that
documents TWI support, like this:
i2c0: i2c@40003000 {
/*
* This i2c node can be TWI, [...].
*/
...
};
If your SoC only has TWIM and TWIS I2C peripherals, you cannot use
this binding. See the "nordic,nrf-twim" binding instead.
Properties
**********
.. tabs::
.. group-tab:: Node specific properties
Properties not inherited from the base binding file.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``pinctrl-0``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.
This property is **required**.
* - ``easydma-maxcnt-bits``
- ``int``
- .. code-block:: none
Maximum number of bits available in the EasyDMA MAXCNT register. This
property must be set at SoC level DTS files.
This property is **required**.
* - ``clock-frequency``
- ``int``
- .. code-block:: none
Initial clock frequency in Hz
* - ``pinctrl-1``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the second state. See pinctrl-0.
* - ``pinctrl-2``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the third state. See pinctrl-0.
* - ``pinctrl-3``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the fourth state. See pinctrl-0.
* - ``pinctrl-4``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the fifth state. See pinctrl-0.
* - ``pinctrl-names``
- ``string-array``
- .. code-block:: none
Names for the provided states. The number of names needs to match the
number of states.
.. group-tab:: Deprecated node specific properties
Deprecated properties not inherited from the base binding file.
(None)
.. group-tab:: Base properties
Properties inherited from the base binding file, which defines
common properties that may be set on many nodes. Not all of these
may apply to the "nordic,nrf-twi" compatible.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``reg``
- ``array``
- .. code-block:: none
register space
This property is **required**.
See :ref:`dt-important-props` for more information.
* - ``interrupts``
- ``array``
- .. code-block:: none
interrupts for device
This property is **required**.
See :ref:`dt-important-props` for more information.
* - ``#address-cells``
- ``int``
- .. code-block:: none
number of address cells in reg property
This property is **required**.
Constant value: ``1``
* - ``#size-cells``
- ``int``
- .. code-block:: none
number of size cells in reg property
This property is **required**.
* - ``status``
- ``string``
- .. code-block:: none
indicates the operational status of a device
Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``
See :ref:`dt-important-props` for more information.
* - ``compatible``
- ``string-array``
- .. code-block:: none
compatible strings
This property is **required**.
See :ref:`dt-important-props` for more information.
* - ``reg-names``
- ``string-array``
- .. code-block:: none
name of each register space
* - ``interrupts-extended``
- ``compound``
- .. code-block:: none
extended interrupt specifier for device
* - ``interrupt-names``
- ``string-array``
- .. code-block:: none
name of each interrupt
* - ``interrupt-parent``
- ``phandle``
- .. code-block:: none
phandle to interrupt controller node
* - ``label``
- ``string``
- .. code-block:: none
Human readable string describing the device (used as device_get_binding() argument)
See :ref:`dt-important-props` for more information.
This property is **deprecated**.
* - ``clocks``
- ``phandle-array``
- .. code-block:: none
Clock gate information
* - ``clock-names``
- ``string-array``
- .. code-block:: none
name of each clock
* - ``dmas``
- ``phandle-array``
- .. code-block:: none
DMA channels specifiers
* - ``dma-names``
- ``string-array``
- .. code-block:: none
Provided names of DMA channel specifiers
* - ``io-channels``
- ``phandle-array``
- .. code-block:: none
IO channels specifiers
* - ``io-channel-names``
- ``string-array``
- .. code-block:: none
Provided names of IO channel specifiers
* - ``mboxes``
- ``phandle-array``
- .. code-block:: none
mailbox / IPM channels specifiers
* - ``mbox-names``
- ``string-array``
- .. code-block:: none
Provided names of mailbox / IPM channel specifiers
* - ``wakeup-source``
- ``boolean``
- .. code-block:: none
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
* - ``power-domain``
- ``phandle``
- .. code-block:: none
Power domain the device belongs to.
The device will be notified when the power domain it belongs to is either
suspended or resumed.
* - ``zephyr,pm-device-runtime-auto``
- ``boolean``
- .. code-block:: none
Automatically configure the device for runtime power management after the
init function runs.